diff --git a/README.md b/README.md
index 8dc6698..a54d845 100644
--- a/README.md
+++ b/README.md
@@ -50,6 +50,30 @@ You will need to do this for all the Printer profiles.
 
 # Changelog
 
+## [v3] - 2021-03-04
+### Notes:
+
+* Added nozzle diameter check on filament profiles
+* Added 0.6n filament profiles
+* 0.6n: Removed Deretract speed (similiar as Retract speed)
+* 0.6n: Removed M221 flow rate in Start/End G-code (respect Filament multiplier instead)
+* 0.6n: Adjusted retraction from 0.1mm to 0.6
+* 0.6n: Added Lift Z 0.2mm
+* 0.6n: Adjusted retract when toolchange from 2mm to 1mm
+* 0.6n: Removed retract before travel 
+* 0.6n: Tuned Bridge flow ratio (from 0.95 to 1.4)
+* 0.6n: Adjusted bridgespeed from 25mm/s to 15mm/s
+* 0.6n: Activated option 'External perimeters first'
+* 0.6n: Deactivated option 'Ensure vertical shell thickness'
+* 0.6n: Adjusted Gap fill speed from 50mm/s to 25mm/s due to printer wobbling
+* 0.6n: Adjusted infill overlap from 30% to 0%
+* 0.6n: Removed max volumetric speed values
+* 0.6n: Adjusted seam position to aligned
+* 0.6n: Tuned support settings
+* 0.6n: Adjusted printspeeds
+
+
+
 ## [v2.2] - 2021-02-16
 ### Notes:
 
diff --git a/Raise3D - E2.ini b/Raise3D - E2.ini
index 0b1f2c5..678a177 100644
--- a/Raise3D - E2.ini	
+++ b/Raise3D - E2.ini	
@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.3.0+win64 on 2021-02-16 at 10:39:23 UTC
+# generated by PrusaSlicer 2.3.0+win64 on 2021-03-04 at 10:04:05 UTC
 
 [print:0.10mm @E2 0.4]
 avoid_crossing_perimeters = 0
@@ -254,7 +254,7 @@ bottom_solid_layers = 5
 bottom_solid_min_thickness = 0.5
 bridge_acceleration = 0
 bridge_angle = 0
-bridge_flow_ratio = 0.95
+bridge_flow_ratio = 1.4
 bridge_speed = 25
 brim_width = 0
 clip_multipart_objects = 1
@@ -265,10 +265,10 @@ default_acceleration = 0
 dont_support_bridges = 1
 draft_shield = 0
 elefant_foot_compensation = 0.2
-ensure_vertical_shell_thickness = 1
-external_perimeter_extrusion_width = 0.65
+ensure_vertical_shell_thickness = 0
+external_perimeter_extrusion_width = 0.68
 external_perimeter_speed = 35
-external_perimeters_first = 0
+external_perimeters_first = 1
 extra_perimeters = 0
 extruder_clearance_height = 27
 extruder_clearance_radius = 52
@@ -288,10 +288,10 @@ infill_anchor = 2.5
 infill_anchor_max = 15
 infill_every_layers = 1
 infill_extruder = 1
-infill_extrusion_width = 0.65
+infill_extrusion_width = 0.68
 infill_first = 0
 infill_only_where_needed = 0
-infill_overlap = 30%
+infill_overlap = 0%
 infill_speed = 70
 inherits = 
 interface_shells = 0
@@ -302,23 +302,23 @@ ironing_speed = 15
 ironing_type = top
 layer_height = 0.15
 max_print_speed = 90
-max_volumetric_speed = 20
+max_volumetric_speed = 0
 min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
-perimeter_extrusion_width = 0.65
+perimeter_extrusion_width = 0.68
 perimeter_speed = 45
 perimeters = 2
 post_process = 
 print_settings_id = 
 raft_layers = 0
 resolution = 0
-seam_position = nearest
+seam_position = aligned
 single_extruder_multi_material_priming = 0
 skirt_distance = 2
 skirt_height = 3
@@ -328,7 +328,7 @@ small_perimeter_speed = 25
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
-solid_infill_extrusion_width = 0.65
+solid_infill_extrusion_width = 0.68
 solid_infill_speed = 60
 spiral_vase = 0
 standby_temperature_delta = -5
@@ -336,22 +336,22 @@ support_material = 0
 support_material_angle = 0
 support_material_auto = 1
 support_material_buildplate_only = 0
-support_material_contact_distance = 0.25
+support_material_contact_distance = 0.2
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0.55
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
-support_material_interface_layers = 4
-support_material_interface_spacing = 0.2
+support_material_interface_layers = 3
+support_material_interface_spacing = 5
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
-support_material_spacing = 3
+support_material_spacing = 2.5
 support_material_speed = 45
 support_material_synchronize_layers = 0
 support_material_threshold = 45
-support_material_with_sheath = 0
-support_material_xy_spacing = 75%
+support_material_with_sheath = 1
+support_material_xy_spacing = 50%
 thin_walls = 0
 threads = 16
 top_fill_pattern = monotonic
@@ -500,8 +500,8 @@ bottom_solid_layers = 4
 bottom_solid_min_thickness = 0.5
 bridge_acceleration = 0
 bridge_angle = 0
-bridge_flow_ratio = 0.95
-bridge_speed = 25
+bridge_flow_ratio = 1.4
+bridge_speed = 15
 brim_width = 0
 clip_multipart_objects = 1
 compatible_printers = 
@@ -511,10 +511,10 @@ default_acceleration = 0
 dont_support_bridges = 1
 draft_shield = 0
 elefant_foot_compensation = 0.2
-ensure_vertical_shell_thickness = 1
-external_perimeter_extrusion_width = 0.65
+ensure_vertical_shell_thickness = 0
+external_perimeter_extrusion_width = 0.68
 external_perimeter_speed = 35
-external_perimeters_first = 0
+external_perimeters_first = 1
 extra_perimeters = 0
 extruder_clearance_height = 27
 extruder_clearance_radius = 52
@@ -531,13 +531,13 @@ gcode_comments = 0
 gcode_label_objects = 0
 infill_acceleration = 0
 infill_anchor = 2.5
-infill_anchor_max = 15
+infill_anchor_max = 12
 infill_every_layers = 1
 infill_extruder = 1
-infill_extrusion_width = 0.65
+infill_extrusion_width = 0.68
 infill_first = 0
 infill_only_where_needed = 0
-infill_overlap = 30%
+infill_overlap = 0%
 infill_speed = 70
 inherits = 
 interface_shells = 0
@@ -548,23 +548,23 @@ ironing_speed = 15
 ironing_type = top
 layer_height = 0.2
 max_print_speed = 90
-max_volumetric_speed = 20
+max_volumetric_speed = 0
 min_skirt_length = 4
 notes = 
-only_retract_when_crossing_perimeters = 0
+only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
-perimeter_extrusion_width = 0.65
+perimeter_extrusion_width = 0.68
 perimeter_speed = 45
 perimeters = 2
 post_process = 
 print_settings_id = 
 raft_layers = 0
 resolution = 0
-seam_position = nearest
+seam_position = aligned
 single_extruder_multi_material_priming = 0
 skirt_distance = 2
 skirt_height = 3
@@ -574,30 +574,30 @@ small_perimeter_speed = 25
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
-solid_infill_extrusion_width = 0.65
-solid_infill_speed = 60
+solid_infill_extrusion_width = 0.68
+solid_infill_speed = 70
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 0
 support_material_angle = 0
 support_material_auto = 1
 support_material_buildplate_only = 0
-support_material_contact_distance = 0.25
+support_material_contact_distance = 0.2
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0.55
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
-support_material_interface_layers = 4
-support_material_interface_spacing = 0.2
+support_material_interface_layers = 3
+support_material_interface_spacing = 5
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
-support_material_spacing = 3
-support_material_speed = 45
+support_material_spacing = 2.5
+support_material_speed = 50
 support_material_synchronize_layers = 0
 support_material_threshold = 45
-support_material_with_sheath = 0
-support_material_xy_spacing = 75%
+support_material_with_sheath = 1
+support_material_xy_spacing = 50%
 thin_walls = 0
 threads = 16
 top_fill_pattern = monotonic
@@ -746,8 +746,8 @@ bottom_solid_layers = 4
 bottom_solid_min_thickness = 0.5
 bridge_acceleration = 0
 bridge_angle = 0
-bridge_flow_ratio = 0.95
-bridge_speed = 25
+bridge_flow_ratio = 1.4
+bridge_speed = 15
 brim_width = 0
 clip_multipart_objects = 1
 compatible_printers = 
@@ -757,10 +757,10 @@ default_acceleration = 0
 dont_support_bridges = 1
 draft_shield = 0
 elefant_foot_compensation = 0.2
-ensure_vertical_shell_thickness = 1
-external_perimeter_extrusion_width = 0.65
-external_perimeter_speed = 35
-external_perimeters_first = 0
+ensure_vertical_shell_thickness = 0
+external_perimeter_extrusion_width = 0.68
+external_perimeter_speed = 72
+external_perimeters_first = 1
 extra_perimeters = 0
 extruder_clearance_height = 27
 extruder_clearance_radius = 52
@@ -772,19 +772,19 @@ first_layer_acceleration = 0
 first_layer_extrusion_width = 0.65
 first_layer_height = 0.3
 first_layer_speed = 15
-gap_fill_speed = 50
+gap_fill_speed = 25
 gcode_comments = 0
 gcode_label_objects = 0
 infill_acceleration = 0
 infill_anchor = 2.5
-infill_anchor_max = 15
+infill_anchor_max = 12
 infill_every_layers = 1
 infill_extruder = 1
-infill_extrusion_width = 0.65
+infill_extrusion_width = 0.68
 infill_first = 0
 infill_only_where_needed = 0
-infill_overlap = 30%
-infill_speed = 70
+infill_overlap = 0
+infill_speed = 72
 inherits = 
 interface_shells = 0
 ironing = 0
@@ -793,62 +793,62 @@ ironing_spacing = 0.15
 ironing_speed = 15
 ironing_type = top
 layer_height = 0.3
-max_print_speed = 90
-max_volumetric_speed = 20
+max_print_speed = 130
+max_volumetric_speed = 0
 min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
-perimeter_extrusion_width = 0.65
-perimeter_speed = 45
-perimeters = 2
+perimeter_extrusion_width = 0.68
+perimeter_speed = 80
+perimeters = 4
 post_process = 
 print_settings_id = 
 raft_layers = 0
 resolution = 0
-seam_position = nearest
+seam_position = aligned
 single_extruder_multi_material_priming = 0
 skirt_distance = 2
 skirt_height = 3
 skirts = 1
 slice_closing_radius = 0.049
-small_perimeter_speed = 25
+small_perimeter_speed = 27
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
-solid_infill_extrusion_width = 0.65
-solid_infill_speed = 70
+solid_infill_extrusion_width = 0.68
+solid_infill_speed = 72
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 0
 support_material_angle = 0
 support_material_auto = 1
 support_material_buildplate_only = 0
-support_material_contact_distance = 0.15
+support_material_contact_distance = 0.2
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0.55
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
-support_material_interface_layers = 4
-support_material_interface_spacing = 0.2
+support_material_interface_layers = 3
+support_material_interface_spacing = 5
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
-support_material_spacing = 3
+support_material_spacing = 2.5
 support_material_speed = 45
 support_material_synchronize_layers = 0
 support_material_threshold = 45
-support_material_with_sheath = 0
-support_material_xy_spacing = 75%
+support_material_with_sheath = 1
+support_material_xy_spacing = 50%
 thin_walls = 0
 threads = 16
 top_fill_pattern = monotonic
 top_infill_extrusion_width = 0.6
-top_solid_infill_speed = 60
+top_solid_infill_speed = 72
 top_solid_layers = 4
 top_solid_min_thickness = 0.6
 travel_speed = 150
@@ -869,8 +869,8 @@ bottom_solid_layers = 3
 bottom_solid_min_thickness = 0.5
 bridge_acceleration = 0
 bridge_angle = 0
-bridge_flow_ratio = 0.95
-bridge_speed = 25
+bridge_flow_ratio = 1.4
+bridge_speed = 15
 brim_width = 0
 clip_multipart_objects = 1
 compatible_printers = 
@@ -880,10 +880,10 @@ default_acceleration = 0
 dont_support_bridges = 1
 draft_shield = 0
 elefant_foot_compensation = 0.2
-ensure_vertical_shell_thickness = 1
+ensure_vertical_shell_thickness = 0
 external_perimeter_extrusion_width = 0.68
 external_perimeter_speed = 35
-external_perimeters_first = 0
+external_perimeters_first = 1
 extra_perimeters = 0
 extruder_clearance_height = 27
 extruder_clearance_radius = 52
@@ -895,7 +895,7 @@ first_layer_acceleration = 0
 first_layer_extrusion_width = 0.65
 first_layer_height = 0.3
 first_layer_speed = 15
-gap_fill_speed = 50
+gap_fill_speed = 25
 gcode_comments = 0
 gcode_label_objects = 0
 infill_acceleration = 0
@@ -906,7 +906,7 @@ infill_extruder = 1
 infill_extrusion_width = 0.68
 infill_first = 0
 infill_only_where_needed = 0
-infill_overlap = 30%
+infill_overlap = 0%
 infill_speed = 70
 inherits = 
 interface_shells = 0
@@ -917,13 +917,13 @@ ironing_speed = 15
 ironing_type = top
 layer_height = 0.35
 max_print_speed = 90
-max_volumetric_speed = 20
+max_volumetric_speed = 0
 min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.68
@@ -933,7 +933,7 @@ post_process =
 print_settings_id = 
 raft_layers = 0
 resolution = 0
-seam_position = nearest
+seam_position = aligned
 single_extruder_multi_material_priming = 0
 skirt_distance = 2
 skirt_height = 3
@@ -951,22 +951,22 @@ support_material = 0
 support_material_angle = 0
 support_material_auto = 1
 support_material_buildplate_only = 0
-support_material_contact_distance = 0.25
+support_material_contact_distance = 0.2
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0.55
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
-support_material_interface_layers = 4
-support_material_interface_spacing = 0.2
+support_material_interface_layers = 3
+support_material_interface_spacing = 5
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
-support_material_spacing = 3
+support_material_spacing = 2.5
 support_material_speed = 50
 support_material_synchronize_layers = 0
 support_material_threshold = 45
 support_material_with_sheath = 0
-support_material_xy_spacing = 75%
+support_material_xy_spacing = 50%
 thin_walls = 0
 threads = 16
 top_fill_pattern = monotonic
@@ -992,8 +992,8 @@ bottom_solid_layers = 3
 bottom_solid_min_thickness = 0.5
 bridge_acceleration = 0
 bridge_angle = 0
-bridge_flow_ratio = 0.95
-bridge_speed = 25
+bridge_flow_ratio = 1.4
+bridge_speed = 15
 brim_width = 0
 clip_multipart_objects = 1
 compatible_printers = 
@@ -1003,10 +1003,10 @@ default_acceleration = 0
 dont_support_bridges = 1
 draft_shield = 0
 elefant_foot_compensation = 0.2
-ensure_vertical_shell_thickness = 1
+ensure_vertical_shell_thickness = 0
 external_perimeter_extrusion_width = 0.68
 external_perimeter_speed = 35
-external_perimeters_first = 0
+external_perimeters_first = 1
 extra_perimeters = 0
 extruder_clearance_height = 27
 extruder_clearance_radius = 52
@@ -1018,7 +1018,7 @@ first_layer_acceleration = 0
 first_layer_extrusion_width = 0.65
 first_layer_height = 0.3
 first_layer_speed = 15
-gap_fill_speed = 50
+gap_fill_speed = 25
 gcode_comments = 0
 gcode_label_objects = 0
 infill_acceleration = 0
@@ -1029,7 +1029,7 @@ infill_extruder = 1
 infill_extrusion_width = 0.68
 infill_first = 0
 infill_only_where_needed = 0
-infill_overlap = 30%
+infill_overlap = 0%
 infill_speed = 70
 inherits = 
 interface_shells = 0
@@ -1040,13 +1040,13 @@ ironing_speed = 15
 ironing_type = top
 layer_height = 0.4
 max_print_speed = 90
-max_volumetric_speed = 20
+max_volumetric_speed = 0
 min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.68
@@ -1056,7 +1056,7 @@ post_process =
 print_settings_id = 
 raft_layers = 0
 resolution = 0
-seam_position = nearest
+seam_position = aligned
 single_extruder_multi_material_priming = 0
 skirt_distance = 2
 skirt_height = 3
@@ -1074,22 +1074,22 @@ support_material = 0
 support_material_angle = 0
 support_material_auto = 1
 support_material_buildplate_only = 0
-support_material_contact_distance = 0.25
+support_material_contact_distance = 0.2
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0.55
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
-support_material_interface_layers = 4
-support_material_interface_spacing = 0.2
+support_material_interface_layers = 3
+support_material_interface_spacing = 5
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
-support_material_spacing = 3
+support_material_spacing = 2.5
 support_material_speed = 50
 support_material_synchronize_layers = 0
 support_material_threshold = 45
-support_material_with_sheath = 0
-support_material_xy_spacing = 75%
+support_material_with_sheath = 1
+support_material_xy_spacing = 50%
 thin_walls = 0
 threads = 16
 top_fill_pattern = monotonic
@@ -1111,7 +1111,7 @@ xy_size_compensation = 0
 bed_temperature = 100
 bridge_fan_speed = 25
 compatible_printers = 
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
 compatible_prints = 
 compatible_prints_condition = 
 cooling = 1
@@ -1165,11 +1165,69 @@ slowdown_below_layer_time = 20
 start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
 temperature = 250
 
+[filament:ABS @E2 0.6n]
+bed_temperature = 100
+bridge_fan_speed = 25
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 4
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1.1
+fan_always_on = 0
+fan_below_layer_time = 30
+filament_colour = #FF8000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 30
+filament_density = 1.12
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 11
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = 0.2
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_type = ABS
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 100
+first_layer_temperature = 250
+full_fan_speed_layer = 0
+inherits = 
+max_fan_speed = 15
+min_fan_speed = 15
+min_print_speed = 15
+slowdown_below_layer_time = 20
+start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
+temperature = 250
+
 [filament:FLEX @E2]
 bed_temperature = 60
 bridge_fan_speed = 80
 compatible_printers = 
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
 compatible_prints = 
 compatible_prints_condition = 
 cooling = 0
@@ -1223,11 +1281,69 @@ slowdown_below_layer_time = 15
 start_filament_gcode = "; Filament gcode\n"
 temperature = 240
 
+[filament:FLEX @E2 0.6n]
+bed_temperature = 60
+bridge_fan_speed = 80
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 0
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1.1
+fan_always_on = 0
+fan_below_layer_time = 100
+filament_colour = #008000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 30
+filament_density = 1.22
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 1.2
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = 0
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_type = FLEX
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 60
+first_layer_temperature = 240
+full_fan_speed_layer = 4
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 15
+slowdown_below_layer_time = 15
+start_filament_gcode = "; Filament gcode\n"
+temperature = 240
+
 [filament:PETG @E2]
 bed_temperature = 70
 bridge_fan_speed = 50
 compatible_printers = 
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
 compatible_prints = 
 compatible_prints_condition = 
 cooling = 1
@@ -1281,11 +1397,69 @@ slowdown_below_layer_time = 15
 start_filament_gcode = "; Filament gcode\nM572 D0 S0.14\nM572 D1 S0.14"
 temperature = 245
 
+[filament:PETG @E2 0.6n]
+bed_temperature = 70
+bridge_fan_speed = 50
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 3
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1.1
+fan_always_on = 1
+fan_below_layer_time = 20
+filament_colour = #FF8000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 50
+filament_density = 1.27
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 8
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = 0.2
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_type = PET
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 70
+first_layer_temperature = 245
+full_fan_speed_layer = 0
+inherits = 
+max_fan_speed = 50
+min_fan_speed = 30
+min_print_speed = 15
+slowdown_below_layer_time = 15
+start_filament_gcode = "; Filament gcode\nM572 D0 S0.14\nM572 D1 S0.14"
+temperature = 245
+
 [filament:PLA @E2]
 bed_temperature = 60
 bridge_fan_speed = 100
 compatible_printers = 
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
 compatible_prints = 
 compatible_prints_condition = 
 cooling = 1
@@ -1339,11 +1513,69 @@ slowdown_below_layer_time = 8
 start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
 temperature = 215
 
+[filament:PLA @E2 0.6n]
+bed_temperature = 60
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FF8000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 30
+filament_density = 1.24
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 15
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 60
+first_layer_temperature = 220
+full_fan_speed_layer = 0
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 25
+slowdown_below_layer_time = 8
+start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
+temperature = 215
+
 [filament:PVA @E2]
 bed_temperature = 50
 bridge_fan_speed = 100
 compatible_printers = 
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
 compatible_prints = 
 compatible_prints_condition = 
 cooling = 0
@@ -1397,11 +1629,69 @@ slowdown_below_layer_time = 10
 start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
 temperature = 215
 
+[filament:PVA @E2 0.6n]
+bed_temperature = 50
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 0
+disable_fan_first_layers = 3
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1.1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #C0C0C0
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 50
+filament_density = 1.23
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 3.8
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 1
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_type = PVA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 50
+first_layer_temperature = 215
+full_fan_speed_layer = 0
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+slowdown_below_layer_time = 10
+start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
+temperature = 215
+
 [filament:WOOD @E2]
 bed_temperature = 60
 bridge_fan_speed = 100
 compatible_printers = 
-compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.4
 compatible_prints = 
 compatible_prints_condition = 
 cooling = 1
@@ -1455,6 +1745,64 @@ slowdown_below_layer_time = 15
 start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
 temperature = 220
 
+[filament:WOOD @E2 0.6n]
+bed_temperature = 60
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_RAISE3D.*/ and printer_notes=~/.*PRINTER_MODEL_E2.*/ and nozzle_diameter[0]==0.6
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1.2
+fan_always_on = 1
+fan_below_layer_time = 100
+filament_colour = #804000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 50
+filament_density = 1.58
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 10
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = 0.2
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 0
+filament_toolchange_delay = 0
+filament_type = WOOD
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 60
+first_layer_temperature = 220
+full_fan_speed_layer = 4
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 15
+slowdown_below_layer_time = 15
+start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
+temperature = 220
+
 [printer:Raise3D E2 0.4 - Dual extrude]
 bed_custom_model = 
 bed_custom_texture = C:\\Users\\vegar\\AppData\\Roaming\\PrusaSlicer-beta\\physical_printer\\Overlay.svg
@@ -1856,7 +2204,7 @@ cooling_tube_length = 5
 cooling_tube_retraction = 91.5
 default_filament_profile = ""
 default_print_profile = 
-deretract_speed = 25,25
+deretract_speed = 0,0
 end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM221 T0 S100 ; reset flow\nM221 T1 S100 ; reset flow\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
 extra_loading_move = -2
 extruder_colour = ;#000000
@@ -1899,12 +2247,12 @@ printer_vendor =
 printhost_apikey = 
 printhost_cafile = 
 remaining_times = 0
-retract_before_travel = 0.6,0.6
+retract_before_travel = 0,0
 retract_before_wipe = 0%,0%
 retract_layer_change = 0,0
-retract_length = 0.1,0.1
-retract_length_toolchange = 2,2
-retract_lift = 0,0
+retract_length = 0.6,0.6
+retract_length_toolchange = 1,1
+retract_lift = 0.2,0.2
 retract_lift_above = 0,0
 retract_lift_below = 0,0
 retract_restart_extra = 0,0
@@ -1934,7 +2282,7 @@ cooling_tube_length = 5
 cooling_tube_retraction = 91.5
 default_filament_profile = ""
 default_print_profile = 
-deretract_speed = 25,25
+deretract_speed = 0,0
 end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM221 T0 S100 ; reset flow\nM221 T1 S100 ; reset flow\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
 extra_loading_move = -2
 extruder_colour = ;
@@ -1977,12 +2325,12 @@ printer_vendor =
 printhost_apikey = 
 printhost_cafile = 
 remaining_times = 0
-retract_before_travel = 0.6,0.6
+retract_before_travel = 0,0
 retract_before_wipe = 0%,0%
 retract_layer_change = 0,0
-retract_length = 0.1,0.1
-retract_length_toolchange = 2,2
-retract_lift = 0,0
+retract_length = 0.6,0.6
+retract_length_toolchange = 1,1
+retract_lift = 0.2,0.2
 retract_lift_above = 0,0
 retract_lift_below = 0,0
 retract_restart_extra = 0,0
@@ -2012,7 +2360,7 @@ cooling_tube_length = 5
 cooling_tube_retraction = 91.5
 default_filament_profile = ""
 default_print_profile = 
-deretract_speed = 25
+deretract_speed = 0
 end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM221 T0 S100 ; reset flow\nM221 T1 S100 ; reset flow\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
 extra_loading_move = -2
 extruder_colour = #FF8040
@@ -2055,12 +2403,12 @@ printer_vendor =
 printhost_apikey = 
 printhost_cafile = 
 remaining_times = 0
-retract_before_travel = 0.6
+retract_before_travel = 0
 retract_before_wipe = 0%
 retract_layer_change = 0
-retract_length = 0.1
+retract_length = 0.6
 retract_length_toolchange = 10
-retract_lift = 0
+retract_lift = 0.2
 retract_lift_above = 0
 retract_lift_below = 240
 retract_restart_extra = 0
@@ -2090,7 +2438,7 @@ cooling_tube_length = 5
 cooling_tube_retraction = 91.5
 default_filament_profile = ""
 default_print_profile = 
-deretract_speed = 25,25
+deretract_speed = 0,0
 end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM221 T0 S100 ; reset flow\nM221 T1 S100 ; reset flow\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
 extra_loading_move = -2
 extruder_colour = ;
@@ -2133,12 +2481,12 @@ printer_vendor =
 printhost_apikey = 
 printhost_cafile = 
 remaining_times = 0
-retract_before_travel = 0.6,0.6
+retract_before_travel = 0,0
 retract_before_wipe = 0%,0%
 retract_layer_change = 0,0
-retract_length = 0.1,0.1
-retract_length_toolchange = 2,2
-retract_lift = 0,0
+retract_length = 0.6,0.6
+retract_length_toolchange = 1,1
+retract_lift = 0.2,0.2
 retract_lift_above = 0,0
 retract_lift_below = 0,0
 retract_restart_extra = 0,0
@@ -2168,8 +2516,8 @@ cooling_tube_length = 5
 cooling_tube_retraction = 91.5
 default_filament_profile = ""
 default_print_profile = 
-deretract_speed = 25
-end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM221 T0 S100 ; reset flow\nM221 T1 S100 ; reset flow\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
+deretract_speed = 0
+end_gcode = M1002 ; Start of End G-code\nG1 E-1 F1800 ; retract\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM106 S0 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)}{endif} F720 ; Move print head up\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} F720 ; Move print head further up\nG28 X0 U0 ; move toolheads to start positions\nG1 Y240 ; Move bed to front and present print\nM84 ; Disable steppers\nM18 ; Disable stepper motors\nM605 S0 ; set to standard mode
 extra_loading_move = -2
 extruder_colour = #FF8040
 extruder_offset = 0x0
@@ -2211,12 +2559,12 @@ printer_vendor =
 printhost_apikey = 
 printhost_cafile = 
 remaining_times = 0
-retract_before_travel = 0.6
+retract_before_travel = 0
 retract_before_wipe = 0%
 retract_layer_change = 0
-retract_length = 0.1
+retract_length = 0.6
 retract_length_toolchange = 10
-retract_lift = 0
+retract_lift = 0.2
 retract_lift_above = 0
 retract_lift_below = 240
 retract_restart_extra = 0
@@ -2224,7 +2572,7 @@ retract_restart_extra_toolchange = 0
 retract_speed = 40
 silent_mode = 0
 single_extruder_multi_material = 0
-start_gcode = M605 S0 ; set to standard mode\nM221 T1 S96 ; set flow rate\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] T1 ; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] T1 ; wait for extruder temp\nG28 ; home all axes\nT1 ; set second toolhead\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
+start_gcode = M605 S0 ; set to standard mode\nG90 ; set printer absolute mode\nM82 ; set extruder to absolute mode\nM106 S0 ; fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM104 S[first_layer_temperature] T1 ; set extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] T1 ; wait for extruder temp\nG28 ; home all axes\nT1 ; set second toolhead\nG1 Z3 F500 ; Move to Z3 for height clearance before Intro line\nG92 E0 ; set position\n; intro line\nG1 Z0.35 F800 ;\nG1 X60 Y-2 F800 ;\nG1 X140 Y-2 E12 F200 ;\nG1 Z5 E15 F200 ; Move to Z5 to prevent dragging nozzle and scratching bed\nG92 E0 ; set position\nG1 F9000.0 ;\nM117 Printing...\nM1001 ; End of Start G-code
 template_custom_gcode = 
 thumbnails = 
 toolchange_gcode = 
@@ -2236,9 +2584,9 @@ wipe = 0
 z_offset = 0
 
 [presets]
-print = 0.20mm @E2 0.4
+print = 0.20mm @E2 0.6
 sla_print = 
 sla_material = 
-printer = Raise3D E2 0.4 - Left head
-filament = PLA @E2
+printer = Raise3D E2 0.6 - Right head
+filament = PLA @E2 0.6n
 physical_printer =