PROJECT NOT UNDER ACTIVE MANAGEMENT
This project will no longer be maintained by Intel.
Intel has ceased development and contributions including, but not limited to, maintenance, bug fixes, new releases, or updates, to this project.
Intel no longer accepts patches to this project.
If you have an ongoing need to use this project, are interested in independently developing it, or would like to maintain patches for the open source software community, please create your own fork of this project.
Contact: webadmin@linux.intel.com
This component implements PLDM Requester functionalities.
This component implements PLDM types as per below table.
| PLDM Type | Supports |
|---|---|
| PLDM Messaging Control and Discovery – DSP0240 v1.0.0 | Implements requester functionality. Discovery of PLDM Terminus, PLDM Types support and the commands supported by PLDM terminus. |
| PLDM for SMBIOS – DSP0246 v1.0.0 | Not supported |
| PLDM for Platform Monitoring and Control – DSP0248 v1.2.0 | Implements requester functionality. Monitoring and control commands to support sensors and effecters. |
| PLDM for BIOS Control and Configuration – DSP0247 v1.0.0 | Not supported |
| PLDM for FRU Data – DSP0257 v1.0.0 | Implements requester functionality. PLDM FRU commands to read/write FRU fields of terminus |
| PLDM for Firmware Update – DSP0267 v1.0.1 | Implements requester functionality. Implements UA (Update Agent) functionality |
| PLDM for Redfish Device Enablement – DSP0218 v1.1.0 | Not supported |
| Reserved | Not supported |
| OEM Specific | Not supported |
This daemon makes use of mctpwplus library to communicate with transport
layer(MCTP) and libpldm_intel library for for encoding/decoding PLDM commands
and PDR parsing. Current implementation includes mapping to MCTP transport
alone. mctpwplus indicates any change(addition/removal) in MCTP network to
PLDM daemon and exposes tx/rx to send/receive the PLDM message.
PLDM Base facilitate the discovery of PLDM capabilities of a device. BMC relies on the PLDM Base command set to further trigger PLDM Type specific functionalities, for example: a device can indicate which PLDM Types are supported using the Get PLDM Types response and BMC will use the response to trigger supported PLDM Type commands.
The PLDM M&C implements:
- Support Central Platform Descriptor Record (PDR) Repository called PrimaryPDR repository, which can hold aggregation of all PDR information within the PLDM subsystem.
- Provide a way to monitor the PLDM Numeric Sensors and expose the values to the D-Bus, so the other applications can use it.
- Provide a way to monitor the PLDM State Sensors and expose the state set values and state change to other applications.
- Provide a way to read and expose the PLDM Numeric Effecters to other applications. Also, provide a mechanism to update the exposed Numeric Effecter value.
- Provide a way to read and expose the PLDM State Effecters to other applications. Also, provide a mechanism to update the exposed Numeric Effecter state.
- Log a redfish event on the state sensor state change.
- Numeric Sensor PDR
- State Sensor PDR
- Numeric Effecter PDR
- State Effecter PDR
- Terminus Locator PDR
- Entity Association
- FRU Record Set PDR
- Sensor Auxiliary Names PDR
- Effecter Auxiliary Names PDR
- Entity Auxiliary Names PDR
- Temperature sensor
- Current sensor
- Voltage sensor
- Power sensor
D-Bus interfaces are supported for any state sensors irrespective of the State Set ID and State Set Values that the sensor supports. But the redfish events for State Sensor state change will be supported for the following State IDs only.
- Operational Fault Status Note: Composite State Sensors are not supported.
- Time Effecter
- Current Effecter
- Voltage Effecter
- Power Effecter
D-Bus interfaces are supported for any state effecter irrespective of the State Set ID and State Set Values that the effecter supports. Note: Composite State Effecters are not supported.
- The PLDM service should perform device discovery and trigger Platform Monitoring and Control for the devices that support this PLDM Type.
- M&C is responsible for fetching the device PDRs.
- BMC can create a system hierarchy based on Entity Association PDR and expose the same on D-Bus.
- The sensors and effecters from the PDRs need to be parsed and enabled. The same should be monitored for any value change and expose it on D-Bus.
- Interested client can use
DumpPDRD-Bus method under interfacexyz.openbmc_project.PLDM.PDRand object path/xyz/openbmc_project/system/<TID>to extract PLDM device PDR.
The following figure illustrates the internals of PLDM M&C.
|---------------------|
| Terminus Init |
|---------|-----------|
|
|
|---------v-----------|
| Platform M&C Init | |----------------------------------------|
|---------|-----------| | * Read full PDR repo |
| | * Parse each PDR |
| | * Create system hierarchy using |
|---------v-----------| | Entity Association PDR |
| PDR Manager |--------->| * Expose entity information along |
|---------|-----------| | with system hierarchy |
| | * Expose DumpPDR method under |
| | PLDM.PDR interface |
| |----------------------------------------|
|
|---------|----------------------------------------------------------------------------|
| Loop n times: For each Numeric Sensor in the PDR |
|---------|----------------------------------------------------------------------------|
| | |
| |------v---------| |--------------------------------------------------| |
| | Numeric Sensor | | * Enable numeric sensor | |
| | Handler Init |----------->| * Extract sensor details like thresholds | |
| |------|---------| | data from Numeric Sensor PDR | |
A | | * Calculate sensor value from sensor reading | V
| |------v--------| | * Provide API to trigger sensor value refresh | |
| | Add Sensor to | | * Expose Sensor.Value, Sensor.Threshold and | |
| | sensor poll |------| | Decorator interfaces | |
| | coroutine | | |--------------------------------------------------| |
| |------|--------| | |
| | | /\ |
| | | / \ |
|---------|---------------|-------------------/ \-----------------------------------|
| | \ /
| | \ /
| | \/
| |
| |
| |
| | |------------------------------------------------------------------------------|
| | | Loop with condition: For each initialized Numeric/State sensor |
| | |------------------------------------------------------------------------------|
| | | |
| | | |------------------| |----------------------------------------------| |
| | | | Poll all sensors | | * Trigger Numeric/State sensor read | |
| |------------------------------------------------------------------->| coroutine |---->| API on every poll interval | |
| A |----------A-------| | * sensor value will be refreshed in | v
| | | | sequential manner (eg: NumericSensor1 | |
| | | | -> NumericSensor2 -> StateSensor1->...) | |
| | | |----------------------------------------------| |
| | | |
| | | /\ |
| | | / \ |
| |-------------|-----------------/ = \-----------------------------------------|
| | \ /
| | \ /
| | \/
| |
|---------|----------------------------------------------------------------------------| |
| Loop n times: For each State Sensor in the PDR | |
|---------|----------------------------------------------------------------------------| |
| | |------------------------------------------------------------|------------------|
| |------v---------| | |--------------------------------------------------| |
| | State Sensor | | | * Enable state sensor | |
| | Handler Init |-----|----->| * Extract sensor details like state set ID, | |
| |------|---------| | | possible states from State Sensor PDR | |
A | | | * Provide API to trigger sensor state change | V
| |------v--------| | | refresh | |
| | Add Sensor to | | | * Expose Sensor.State and Decorator | |
| | sensor poll |------| | interfaces | |
| | coroutine | | * Add redfish log for any state sensor state | |
| |------|--------| | change | |
| | | | |
| | |--------------------------------------------------| |
| | /\ |
| | / \ |
|---------|-----------------------------------/ \-----------------------------------|
| \ /
| \ /
| \/
|
|
|---------|----------------------------------------------------------------------------|
| Loop n times: For each Numeric Effecter in the PDR |
|---------|----------------------------------------------------------------------------|
| | |
| |------v-----------| |--------------------------------------------------| |
| | Numeric Effecter | | * Enable Numeric Effecter | |
| | Handler Init |--------->| * Extract sensor details like max-settable | |
| |------|-----------| | and min-settable from Numeric Effecter PDR | |
A | | * Calculate effecter value from effecter | V
| | | reading | |
| | | * Calculate settable value from user input | |
| | | * Expose Effecter.Value, Effecter.SetEffecter | |
| | | and Decorator interfaces | |
| | |--------------------------------------------------| |
| | /\ |
| | / \ |
|---------|-----------------------------------/ \-----------------------------------|
| \ /
| \ /
| \/
|
|
|---------|----------------------------------------------------------------------------|
| Loop n times: For each State Effecter in the PDR |
|---------|----------------------------------------------------------------------------|
| | |
| |------v-----------| |--------------------------------------------------| |
| | State Effecter | | * Enable State Effecter | |
| | Handler Init |--------->| * Extract Effecter details like State Set ID, | |
| |------------------| | possible states from State Effecter PDR | |
A | * Expose Effecter.State, Effecter.SetEffecter | V
| | and Decorator interfaces | |
| |--------------------------------------------------| |
| /\ |
| / \ |
|---------------------------------------------/ \-----------------------------------|
\ /
\ /
\/
If the PLDM terminus supports Entity Association PDR, it will be used to create a system hierarchy to the PLDM terminus.
The below diagram shows the PLDM terminus (Add-in-Card) having another associated entity (Processor). Also, the hierarchy shows the sensors and effecters associated to each entity.
Note: The sensor/effecter names will have device full name as prefix to avoid duplicate names when more than one PLDM terminus has same name. The naming format is:
- Entity -
<EntityName> - Sensor -
<DeviceFullName>_<SensorName> - Effecter -
<DeviceFullName>_<EffecterName>
The DeviceName is read from the Entity Auxiliary Names PDR of the root Entity
Association PDR. If the PDR is not available, the default name PLDM_Device
will be assigned. DeviceLocation is read from the LocationCode property in mctpd
used for distinguishing devices. Both DeviceName and DeviceLocation forms the full
name of a device (hereinafter referred to as DeviceFullName). The format is
<DeviceLocation>_<DeviceName> when location is available, <DeviceName>_<TID>
otherwise.
EntityName is also read from Entity Auxiliary Names PDR, if it has no auxiliary
name, default value will be <EntityType>_<InstanceNumber>_<ContainerID>.
SensorName/EffecterName are read from Sensor/Effecter Auxiliary Names PDR. If there
is no matched PDR, default PLDM_Sensor/Effecter_<SensorID> will be used for the
Sensor/EffecterName part. The full name is prefixed with DeviceFullName.
Below is an example of pldmd DBus hierarchy.
(LocationCode=PCIe1, DeviceName=Add-in-card, SensorName=Numeric/EffecterSensorX)
/xyz/openbmc_project/system
|_/xyz/openbmc_project/system/<TID>
|_/xyz/openbmc_project/system/<TID>/Add-in-card
| |_/xyz/openbmc_project/system/<TID>/Add-in-card/PCIe_1_Add-in-card_NumericSensor1
| |_/xyz/openbmc_project/system/<TID>/Add-in-card/PCIe_1_Add-in-card_StateSensor1
| |_/xyz/openbmc_project/system/<TID>/Add-in-card/PCIe_1_Add-in-card_StateSensor2
| |_/xyz/openbmc_project/system/<TID>/Add-in-card/PCIe_1_Add-in-card_NumericEffecter1
| |_/xyz/openbmc_project/system/<TID>/Add-in-card/PCIe_1_Add-in-card_StateEffecter1
|_/xyz/openbmc_project/system/<TID>/Add-in-card/Processor
|_/xyz/openbmc_project/system/<TID>/Add-in-card/Processor/PCIe_1_Add-in-card_NumericSensor1
|_/xyz/openbmc_project/system/<TID>/Add-in-card/Processor/PCIe_1_Add-in-card_NumericSensor2
|_/xyz/openbmc_project/system/<TID>/Add-in-card/Processor/PCIe_1_Add-in-card_StateEffecter1
PLDM.Entity, PLDM.NumericSensor, PLDM.StateSensor, PLDM.NumericEffecter,
PLDM.StateEffecter interfaces shall be exposed by entity, sensors or
effecters of the system hierarchy.
BMC supports thermal, power, current and voltage numeric sensors. Each sensor
type will expose Sensor.Value, State.Decorator.Availability,
State.Decorator.OperationalStatus and Sensor.Threshold interfaces as per
phosphor-dbus-interfaces. Sensor.Threshold interface will send threshold
crossing event (D-Bus signal) if sensor values are crossed. The sensor units
can be decoded from the sensor object paths as per Table 1.
Table 1
|--------------|------------------------------------|------------------|
| Sensor Type | Base Object path | Sensor unit |
|--------------|------------------------------------|------------------|
| Thermal | /xyz/openbmc_project/sensors | Degree Celsius |
| | /temperature | |
|--------------|------------------------------------|------------------|
| Power | /xyz/openbmc_project/sensors | Watt |
| | /power | |
|--------------|------------------------------------|------------------|
| Current | /xyz/openbmc_project/sensors | Ampere |
| | /current | |
|--------------|------------------------------------|------------------|
| Voltage | /xyz/openbmc_project/sensors | Volts |
| | /voltage | |
|--------------|------------------------------------|------------------|
BMC exposes Sensor.State, State.Decorator.Availability and
State.Decorator.OperationalStatus interfaces under the D-Bus object path
/xyz/openbmc_project/pldm/<TID>/state_sensor/<SensorName>. The Sensor.State
interface exposes D-Bus properties StateSetId, PossibleStates,PreviousState
and CurrentState properties. PLDM service will log any state sensor state
change as a redfish event log.
The Available property under State.Decorator.Availability interface and
Functional property under State.Decorator.OperationalStatus interfaces
are mapped to PLDM numeric and state sensor operational state, refer
below table 2.
Table 2
|-------------------------------|----------------|--------------------|
| PLDM Sensor Operational State | Available | Functional |
|-------------------------------|----------------|--------------------|
| Enabled | True | True (Can be false |
| | | in case of error) |
|-------------------------------|----------------|--------------------|
| Disabled | True | False |
| | | |
|-------------------------------|----------------|--------------------|
| Unavailable | False | False |
| | | |
|-------------------------------|----------------|--------------------|
Note: Other PLDM sensor operational states (statusUnknown, failed,
initializing, shuttingDown and inTest) are not supported.
- BMC supports time, power, current and voltage numeric sensors.
- Each sensors type will expose
Effecter.Value,State.Decorator.Availability,State.Decorator.OperationalStatusandEffecter.SetEffecter. Effecter.Valueinterface exposesMaxValue,MinValueandValueproperties.Effecter.SetNumericEffecterinterface exposesSetEffecterD-Bus method to set Numeric Effecter value.
The effecter units can be decoded from the effecter object paths as per Table 3.
Table 3
|----------------|-------------------------------|--------------------|
| Effecter Type | Base Object path | Effecter unit |
|----------------|-------------------------------|--------------------|
| Time | /xyz/openbmc_project/pldm | Seconds |
| | /<TID>/effecter/time | |
|----------------|-------------------------------|--------------------|
| Power | /xyz/openbmc_project/pldm | Watt |
| | /<TID>/effecter/power | |
|----------------|-------------------------------|--------------------|
| Current | /xyz/openbmc_project/pldm | Ampere |
| | /<TID>/effecter/current | |
|----------------|-------------------------------|--------------------|
| Voltage | /xyz/openbmc_project/pldm | Volts |
| | /<TID>/effecter/voltage | |
|----------------|-------------------------------|--------------------|
BMC exposes the Effecter.State, State.Decorator.Availability and
State.Decorator.OperationalStatus interfaces under the D-Bus object path
/xyz/openbmc_project/pldm/<TID>/state_effecter/<EffecterName>.
The Effecter.State interface exposes the D-Bus properties StateSetId
PossibleStates, PendingState and CurrentState properties.
Effecter.SetStateEffecter interfaces expose SetEffecter D-Bus method to set
State Effecter state.
The Available property under State.Decorator.Availability interface and
Functional property under State.Decorator.OperationalStatus interfaces are
mapped to PLDM effecter operational state, refer below table 4.
Table 4
|---------------------------------|----------------|--------------------|
| PLDM Effecter Operational State | Available | Functional |
|---------------------------------|----------------|--------------------|
| Enabled-updatePending | True | True (Can be false |
| Enabled-noUpdatePending | | in case of error) |
|---------------------------------|----------------|--------------------|
| Disabled | True | False |
| | | |
|---------------------------------|----------------|--------------------|
| Unavailable | False | False |
| | | |
|---------------------------------|----------------|--------------------|
Note: Other PLDM effecter operational states (statusUnknown, failed,
initializing, shuttingDown and inTest) are not supported.
Below table provides the D-Bus interface details.
|-------------------------------|----------------------------|------------------------------------|
| Interface | Description | Methods/Properties |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide | Properties: |
| PLDM.Entity | PLDM entity information | Name: EntityContainerID |
| | | Type: uint16 |
| | | Description: The containerID |
| | | for the entity |
| | | |
| | | Name: EnityInstanceNumber |
| | | Type: uint16 |
| | | Description: The instance |
| | | number of the entity |
| | | |
| | | Name: EnityType |
| | | Type: uint16 |
| | | Description: The type |
| | | of the entity |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide PLDM | TBD (e.g.: Sensor details |
| PLDM.NumericSensor | Numeric Sensor information| from PDR) |
| | | |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide PLDM | TBD (e.g.: Sensor details |
| PLDM.StateSensor | State Sensor information | from PDR) |
| | | |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide PLDM | TBD (e.g.: Effecter details |
| PLDM.NumericEffecter | Numeric Effecter | from PDR) |
| | information | |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide PLDM | TBD (e.g.: Effecter details |
| PLDM.StateEffecter | Numeric State | from PDR) |
| | information | |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide | For more details refer |
| Sensor.Value | Numeric sensor readings | [phosphor-dbus-interfaces] |
| | | (https://github.com/openbmc/ |
| | | phosphor-dbus-interfaces/blob/ |
| | | master/xyz/openbmc_project/ |
| | | Sensor/Value.interface.yaml) |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide | For more details refer |
| Sensor.Threshold. | critical class sensor | [phosphor-dbus-interfaces] |
| Critical | thresholds for numeric | (https://github.com/openbmc/ |
| | sensors | phosphor-dbus-interfaces/blob/ |
| | | master/xyz/openbmc_project/Sensor |
| | | /Threshold/Critical.interface. |
| | | yaml) |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide | For more details refer |
| Sensor.Threshold.Warning | warning class sensor | [phosphor-dbus-interfaces] |
| | thresholds | (https://github.com/openbmc/ |
| | | phosphor-dbus-interfaces/blob/ |
| | | master/xyz/openbmc_project/Sensor |
| | | /Threshold/Warning.interface. |
| | | yaml) |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to indicate the | For more details refer |
| Sensor.Decorator. | availability status of | [phosphor-dbus-interfaces] |
| Availability | the object | (https://github.com/openbmc/ |
| | | phosphor-dbus-interfaces/blob/ |
| | | master/xyz/openbmc_project/State |
| | | /Decorator/Availability. |
| | | interface.yaml) |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to indicate the | For more details refer |
| Sensor.Decorator. | Operational status of | [phosphor-dbus-interfaces] |
| OperationalStatus | the object | (https://github.com/openbmc/ |
| | | phosphor-dbus-interfaces/blob/ |
| | | master/xyz/openbmc_project/State |
| | | /Decorator/OperationalStatus. |
| | | interface.yaml) |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide | Properties: |
| Sensor.State | State Sensor information | Name: CurrentState |
| | | Type: uint8 |
| | | Description: Represent most |
| | | recently assessed state |
| | | of the state sensor |
| | | |
| | | Name: PreviousState |
| | | Type: uint8 |
| | | Description: Represents state |
| | | that the CurrentState was |
| | | entered from |
| | | |
| | | Name: StateSetID |
| | | Type: uint16 |
| | | Description: A numeric value |
| | | that identifies the PLDM |
| | | State Set that is used with |
| | | this sensor |
| | | |
| | | Name: PossibleStates |
| | | Type: array[uint8] |
| | | Description: A numeric value |
| | | that identifies the PLDM |
| | | State Set values that are |
| | | used with this sensor |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide | Properties: |
| Effecter.Value | numeric effecter value | Name: MaxValue |
| | information | Type: double |
| | | Description: The maximum |
| | | legal setting value that the |
| | | effecter accepts |
| | | |
| | | Name: MinValue |
| | | Type: double |
| | | Description: The minimum |
| | | legal setting value that the |
| | | effecter accepts |
| | | |
| | | Name: Value |
| | | Type: double |
| | | Description: The present |
| | | numeric value setting of |
| | | the effecter |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide | Method: |
| Effecter. | numeric effecter update | Name: SetEffecter |
| SetNumericEffecter | mechanism | Description: Set the effecter |
| | | value |
| | | Parameters: |
| | | |
| | | Name: Value |
| | | Type: double |
| | | Description: The setting |
| | | value of numeric effecter |
| | | being requested |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide | Properties: |
| Effecter.State | State effecter State | Name: CurrentState |
| | information | Type: uint8 |
| | | Description: The present |
| | | state of the effecter |
| | | |
| | | Name: PendingState |
| | | Type: double |
| | | Description: If the value of |
| | | effecter has an updatePending,|
| | | this field returns the value |
| | | for the requested state that |
| | | is presently being processed. |
| | | Otherwise, this field returns |
| | | the present state of the |
| | | effecter. |
| | | |
| | | Name: StateSetID |
| | | Type: uint16 |
| | | Description: A numeric value |
| | | that identifies the PLDM |
| | | State Set that is used with |
| | | this effecter |
| | | |
| | | Name: PossibleStates |
| | | Type: array[uint8] |
| | | Description: A numeric value |
| | | that identifies the PLDM |
| | | State Set value that is used |
| | | with this effecter |
|-------------------------------|----------------------------|------------------------------------|
| xyz.openbmc_project. | Implement to provide | Method: |
| Effecter. | a state effecter update | Name: SetEffecter |
| SetStateEffecter | mechanism | Description: Set the effecter |
| | | state |
| | | Parameters: |
| | | |
| | | Name: State |
| | | Type: uint8_t |
| | | Description: The setting |
| | | value of state effecter |
| | | being requested |
|-------------------------------|----------------------------|------------------------------------|
PLDM service will read each sensor value on every poll interval and update the D-Bus interfaces accordingly. Each sensor will be polled in a sequential manner on every poll interval. Current configured value of poll interval is 500ms. If the PLDM service identifies a new device, then sensor polling will be paused temporarily to give priority for device initialisation. Also, sensor polling will be paused when a PLDM firmware update is initiated.
This component implements
- Firmware update for the devices (add-in cards or on-board devices), which supports the PLDM firmware update.
- Firmware update for multiple devices of same type sequentially.
- Expose information of PLDM Firmware update capable devices.
- PLDM Firmware update over MCTP Transport.
- Image signature or signing verification must be done in Firmware Device (FD) side and BMC (Update Agent) will just perform compatible check as per the DSP0267 spec. Note: BMC may elect to verify overall image signature, if needed. i.e. BMC vendor, can do additional sign of the PLDM image to make sure only those approved / verified are allowed to do update. This is extra step and is not replacement to image signature or signing verification done by Firmware Device (FD).
- Bundled firmware update (Single PLDM update package, containing multiple firmware component images - Say PSU, NIC firmware etc.) support is out of scope.
This design is compliant to DSP0267 version 1.0.1 and holds good when moving to next version DSP0267(1.1.0).
This specification identifies a common method to use PLDM messaging to transfer one or more component images to the Firmware Device (FD) within the PLDM subsystem and thereby avoids the use of host operating system-based tools and utilities. The basic format that is used for sending the PLDM messages is defined in DSP0240. The format that is used for carrying the PLDM messages over a particular transport or medium is given in companion documents to the base specification. For example, DSP0241 defines how the PLDM messages are formatted and sent using MCTP as the transport.
The FD is the minimum hardware unit that the PLDM-based firmware update is applied to and with which the Update Agent (UA) communicates to accomplish the update. The Firmware Update Package for an FD contains an individual component image or a group of component images that is known as a component image set. This firmware update package is processed to update each firmware component of the FD during the PLDM update.
Each type of FD has a globally unique identity, which can be used to distinguish it from other types of FDs. A device identifier record consists of a set of device descriptors, which are typically based on industry standard definitions, and is used to describe an FD type. For example, the descriptors for PCI devices include PCI Vendor ID and PCI Device ID.
Figure: High level architecture flow of FW update (through PLDM)
PLDM FWU |----------| |----------| |-------------------| |---------------|
------------>| Redfish |---->| Redfish |---->| OpenBMC |----->|Add-In Card(FD)|
Package | Client | | Interface| | | |---------------|
|----------| |----------| | |-----------| |
| | Redfish | |
| | daemon | | |----------------|
| |-----|-----| |----->|On Board device |
| | | |----------------|
| |-----|-----| |
| | PLDM FW | |
| | Daemon(UA)| |
| |-----------| |
|-------------------|
PLDM daemon gets the list of PLDM capable devices from transport layer(like MCTP) and checks if the devices support PLDM firmware update by running PLDM base commands. When a PLDM capable device is added or removed dynamically, PLDM daemon will be notified by transport layer. For the newly added device PLDM daemon runs the base commands to check PLDM capabilities. PLDM daemon deletes the resources allocated for the removed device.
The FD is the minimum hardware unit that the PLDM-based firmware update is applied to and with which the Update Agent (UA) communicates to accomplish the update.
PLDM daemon sends inventory commands to each FD. As per DSP0267 version 1.0.1, there are two inventory commands,
-
QueryDeviceIdentifiers: This command is used by the UA to obtain the firmware identifiers for the FD.
-
GetFirmwareParameters: This command is used by the UA to acquire the component details such as classification types and corresponding versions of the FD.
Inventory information is exposed to D-Bus and D-Bus objects will be described in the later sections.
Figure: High Level PLDM Firmware Update Flow
PLDM Software Manager Redfish Update Service
| | |
|-----| 1. PLDM daemon queries the transport service | |
| | (like MCTP) to determine PLDM capable | |---------|
| | devices, | | User | initiates
| | 2. Execute PLDM device discovery commands for | | FWU | ( Post Method)
| | each device and verify the PLDM FW update | |-------->|
| | support. | |
| | 3. Execute inventory commands for each FD and | |
|---->| expose information over D-Bus for upper | |
| layer consumption. | |
| | |
| | PLDM FWU package |
| |<---------------------------------|
| | kept in / tmp / images |
| | |
| | |
| |------------| |
| | Verify | PLDM |
| | package | header |
| | identifier | |
| |----------->| |
| | |
| | |
| Initiate update by D-Bus method call | |
|<----------------------------------------------| |
| | |
|-----| | |
| | Parse the package and find out target device | |
| | using device descriptors. | |
|---->| | |
| | |
|-----| | |
| | Run sequence of firmware update commands | |
| | as described in spec DSP0267(1.0.1) | |
|---->| | |
| | |
| Update the firmware activation status and | |
|---------------------------------------------->| |
| progress percentage to software-manager with | |
| D-Bus calls | |
| | |
| | |
User interfaces (like Redfish) are used to upload the PLDM package to the staging area of BMC. Software-manager listens to the changes on staging area and validates the image for PLDM type. It then exposes a D-Bus object that will be described in the later sections. Once verification is done, it notifies the PLDM daemon with a method call to initiate the firmware update.
PLDM Daemon proceeds to parse the firmware package header. It determines the target device by matching the package provided device descriptors with the ones obtained by query device identifiers command.
BMC runs a sequence of firmware update commands to target FD as described in the sections 6.4 and 6.5 Of DSP0240(1.0.1).
There are three additional commands which UA can send to FD,
Get Status– Sending this command to the FD, BMC can know the status of the update at any time.Cancel Update Component- Sending this command to the FD, BMC can cancel the update of current component.Cancel Update- Sending this command to the FD, BMC can cancel the update.
If the firmware update is successful, FD goes for reset.
The PLDM firmware update package contains two major sections:
- Firmware Package Header: It is required to describe the firmware devices that the package is intended to update and component images that the firmware update package contains.
- Firmware Package Payload: It contains the individual component images that can be transferred to the firmware devices.
More details of the PLDM package is described in section 7 of DSP0267.
Figure: PLDM Firmware Update Package
|--------- |---- |--------------------------------|
| | | Package Header Information |
| Firmware | |--------------------------------|
| Package----| | Firmware Device ID Records |
| Header | | & Descriptors |
| | |--------------------------------|
Firmware | | | Component Image Information |
Update -------| |-------|--------------------------------|
Package | | | Component Image 1 |
| Firmware | |--------------------------------|
| Package----| | Component Image 2 |
| Payload | |--------------------------------|
| | | ... |
| | |--------------------------------|
| | | Component Y |
|--------- |---- |--------------------------------|
The below are the objects exposed by PLDM daemon on discovery of PLDM FW update capable devices. These will be picked by redfish automatically.
Object path: /xyz/openbmc_project/software/<entity_name>
Entity name will be taken from PLDM FRU data.
Example: /xyz/openbmc_project/software/NIC0
Interfaces:
xyz.openbmc_project.Software.Activation, which describes firmware update activation status. There could be some devices which supports inventory command, but does not support PLDM firmware update. Activation property can be used to determine whether the device supports firmware update or not.xyz.openbmc_project.Software.Version, which describes the version of the firmware image.xyz.openbmc_project.Association.Definitions, which defines the association of the FD with the inventory item.
Below D-Bus object will be exposed by software-manager, when the PLDM image is uploaded for firmware update.
Service: xyz.openbmc_project.Software.BMC.Updater
object path: /xyz/openbmc_project/software/<ImageHash>
Interfaces:
xyz.openbmc_project.Software.Activation, which describes firmware update activation status.xyz.openbmc_project.Software.Version, which describes the version of the firmware image.xyz.openbmc_project.Software.ActivationProgress, which shows the firmware update progress.xyz.openbmc_project.Software.ImageTargets, which shows the list of target devices which the user intends to update. ImageTargets property is an array of strings. Redfish updates this property based on the httpPushUri arguments. Software-manager passes it to pldmd in the method StartFWUpdate as an argument. PLDM daemon uses ImageTargets to identity the target firmware device.
Note: If ImageTargets is empty, PLDM daemon updates all the devices for which device descriptors are matched.
The below are the D-Bus objects exposed by PLDM daemon to give additional information to the user which can help during validation.
/xyz/openbmc_project/pldm/fwu
|--xyz.openbmc_project.PLDM.FWU.FWUBase
|
|__/xyz/openbmc_project/pldm/fwu/<TerminusID>
|
|__/xyz/openbmc_project/pldm/fwu/<TerminusID>/deviceDescriptors
| |--xyz.openbmc_project.PLDM.FWU.PCIDescriptor
| |--xyz.openbmc_project.PLDM.FWU.IANADescriptor
| |--xyz.openbmc_project.PLDM.FWU.PnPDescriptor
| |--xyz.openbmc_project.PLDM.FWU.ACPIDescriptor
|
|__/xyz/openbmc_project/pldm/fwu/<TerminusID>/componentImageSetInfo
| |--xyz.openbmc_project.PLDM.FWU.ActiveComponentImageSetInfo
| |--xyz.openbmc_project.PLDM.FWU.PendingComponentImageSetInfo
|
|__/xyz/openbmc_project/pldm/fwu/<TerminusID>/componentImageSetInfo/component_<component_no>
|--xyz.openbmc_project.PLDM.FWU.ActiveComponentInfo
|--xyz.openbmc_project.PLDM.FWU.PendingComponentInfo
|--xyz.openbmc_project.PLDM.FWU.ComponentActivationMethods
|--xyz.openbmc_project.PLDM.FWU.CapabilitiesDuringUpdate
Note: Descriptor for a device can be defined by one of the following (PCI Vendor ID, IANA Enterprise ID, UUID, PnP Vendor ID, or ACPI Vendor ID) and the corresponding descriptor's interface is exposed by the Device Descriptors object. No new UUID descriptor interface is defined as the existing UUID interface will be used.
It is exposed by the object /xyz/openbmc_project/pldm/fwu with the
following interface,
xyz.openbmc_project.pldm.FWUBaseexposes a method "StartFWUpdate" by which PLDM FWU can be initiated. PLDM firmware image path and target firmware update devices are passed as arguments to this method.
Each FW update capable device information is exposed by the object
/xyz/openbmc_project/pldm/fwu/<TerminusID>.
It will have the following objects,
- Device Descriptors
- Component Image Set Information
- Component Image Information (Each component is exposed as an object)
Device Descriptors are exposed under the object path
/xyz/openbmc_project/pldm/fwu/deviceDescriptors with one of the
following interfaces.
xyz.openbmc_project.PLDM.FWU.PCIDescriptor, which exposes the PCI device descriptors. If the FD is a PCI device, then this interface will be exposed by the device descriptors object.xyz.openbmc_project.PLDM.FWU.IANADescriptor, which exposes the IANA descriptor properties. If FD have IANA Enterprise ID as the descriptor type, then this interface will be exposed by the device descriptors object.xyz.openbmc_project.PLDM.FWU.PnPDescriptor, which exposes the PnP descriptor properties. If FD have PnP vendor ID as the descriptor type, then this interface will be exposed by the device descriptors object.xyz.openbmc_project.PLDM.FWU.ACPIDescriptor, which exposes the ACPI descriptor properties. If FD have ACPI vendor ID as the descriptor type, then this interface will be exposed by the device descriptors object.
Component Image Set Info is exposed under the object path
/xyz/openbmc_project/pldm/fwu/componentImageSetInfo with the following
interface.
xyz.openbmc_project.PLDM.FWU.ActiveComponentImageSetInfo, which exposes the active component image set properties.xyz.openbmc_project.PLDM.FWU.PendingComponentImageSetInfo, which exposes the pending component image set properties.
Component Image Info is exposed under the object path
/xyz/openbmc_project/pldm/fwu/componentImageSetInfo/componentInfo_<component_no>
with the following interface
xyz.openbmc_project.PLDM.FWU.ActiveComponentInfo, which exposes the component image properties.xyz.openbmc_project.PLDM.FWU.PendingComponentInfo, which exposes the pending component image properties.xyz.openbmc_project.PLDM.FWU.CapabilitiesDuringUpdate, which exposes the capabilities of the component during update.xyz.openbmc_project.PLDM.FWU.ComponentActivationMethods, which exposes the component activation methods.
The PLDM FRU implements:
- PLDM Command - GetFRUTableMetadata Requester
- PLDM Command - GetFRURecordTable Requester
- PLDM Command - SetFRURecordTable Requester
After the device discovery the Platform FRU initialization will be triggered. FRU is responsible for fetching the device inventory records that provide platform asset information including part number, serial number and manufacturer. The FRU Record Table typically resides in a non-volatile memory accessible by the management controller and contains one or more FRU records. BMC can create FRU objects based on PLDM terminus, which supports FRU specification and expose the same on D-Bus. The FRU inventory records from the terminus need to be parsed and enabled and should be allowed to set via the setFRU method using D-Bus call.
The following figure illustrates the internals of PLDM FRU:
/\ |---------------|
/ \ | PLDM FRU |
/ \ | Init |
/ \ |---------------|
/ First \ |
/Invocation\<-----------------------------|
\ ? / |
\ / | [TID]
\ / |
\ / |
\ / |
\/ V
| /\
| / \
| / \
| / \ |--------------|
| [No] /Get FRU \ | User invokes |
[YES] | |--------/ Metadata \ <-----------| | Set FRU |
| | \ Done? / | |--------------|
| | \ / | |
| | \ / | |
| | \ / | |
| | \ / | |
| | \/ | |
| | | | |
| | [YES] | | |
| | | Re-query FRU data | [TID]
| | V for verification |
| | /\ | |
| | / \ | |
V | / \ | V
|---------------| | / \ | |----------------|
| Expose Set | | / \ | | Set FRU |
| FRU Interface | | [No] / Get FRU \ |---------| Commands |
|---------------| |<-------/ Table \ |----------------|
| \ data done? /
| \ /
| \ /
| \ /
| \ /
| \ /
| \/
| |
| [YES] |
| |
| V
| |---------------|
| | Expose FRU |
| | Data on D-Bus |
| |---------------|
|
V
|-------------|
| FRU Object |
| Path/[TID] |
| Not created |
|-------------|
- PLDM FRU Init:
- FRU init exposes
xyz.openbmc_project.PLDM.SetFRUinterface under/xyz/openbmc_project/pldm/fruobject path. - It also exposes FRU properties under
/xyz/openbmc_project/pldm/fru/tidobject path on PLDM Get FRU commands success. In case of failure, the path is not created.
- FRU init exposes
- Get FRU Metadata Command: (2-4 have Get FRU commands and flow)
- Fetch and store FRUTableMaximum size, FRUTableLength and Checksum with TID map for further check.
- Get FRU Record Table data Command:
- Check for transfer flag for multipart transfer.
- Get final FRU record table.
- Calculate and verify CRC with metadata checksum.
- Parsing FRU table for getting each TLV.
- Add FRU objects to D-bus representation.
- Expose FRU data on D-bus:
- Populate FRU properties under
xyz.openbmc_project.Inventory.Source.PLDM.FRU
- Populate FRU properties under
- User invokes SetFRU D-bus method that internally invokes
SetFRUcommands:- Send Set FRU table data using SetFRU method,
busctl call xyz.openbmc_project.pldm xyz/openbmc_project/pldm/fru xyz.openbmc_project.PLDM.SetFRU SetFRU yay tid array_of_general_to_EM_records - Re-query FRU data via PLDM Get commands and update the FRU fields accordingly.
- If [TID] found in terminus FRU map, then clear all TID information from maps and re-create interface with new FRU details.
- If [TID] not found in terminus FRU map, then continue with Get FRU
commands and initialize FRU interface for the first time via
SetFRU. - PLDM Get FRU commands are used to verify whether new FRU details are updated well under FRU interface. In case of failure, the path with TID is not created.
- Send Set FRU table data using SetFRU method,
If the PLDM terminus supports FRU specification, it will be used to create
the object paths of the terminus. The below diagram shows PLDM terminus
(Add-in-Card) having FRU information. FRU information for each PLDM terminus is
located under xyz.openbmc_project.Inventory.Source.PLDM.FRU interface.
busctl tree xyz.openbmc_project.pldm
└─/xyz
└─/xyz/openbmc_project
├─/xyz/openbmc_project/pldm
│ ├─/xyz/openbmc_project/pldm/fru
│ │ ├─/xyz/openbmc_project/pldm/fru/4
│ │ └─/xyz/openbmc_project/pldm/fru/5
The FRU object path exposes SetFRU method.
busctl introspect xyz.openbmc_project.pldm /xyz/openbmc_project/pldm/fru
xyz.openbmc_project.PLDM.SetFRU
.SetFRU method yay i -
FRU D-Bus interface details are described in phosphor-dbus-interfaces.
https://github.com/openbmc/phosphor-dbus-interfaces/blob/master/xyz/openbmc_project/Inventory/Source/PLDM/FRU.interface.yaml
- OEM FRU representation of PLDM terminus
- IPMI FRU to PLDM FRU mapping
- EEPROM based PLDM FRU
- Set FRU on field basis