Skip to content

Latest commit

 

History

History
120 lines (84 loc) · 6.38 KB

How_To_Add_New_Platform.md

File metadata and controls

120 lines (84 loc) · 6.38 KB
Raw

How to Add a New Platform

Since the esp-at project supports different platform, for example, ESP32 UART AT, ESP32 SDIO AT, even supports ESP8266 AT, when compiling the esp-at project, users can set different configurations to generate AT firmware for different ESP modules. The detailed information are in the esp-at/module_config directory. Default configuration is the "PLATFORM_ESP32" for ESP-WROOM-32.
Please note that if you use a different bus (for example, SDIO, SPI or other buses) instead of UART, then you cannot use the default module_espxxxx_default directly, you need to re-configure it in the menuconfig.
Herein, we provide an example of the ESP32 SDIO AT to show how to set a new platform for the esp-at project.

1. Create a New Platform

For example, to name the platform as "PLATFORM_ESP32", the module as "WROOM32-SDIO", we need to open the components/customized_partitions/raw_data/factory_param/factory_param_data.csv and add a new row of the new platform at the end.

platform module_name magic_flag version module_id tx_max_power start_channel channel_num country_code uart_baudrate uart_tx_pin uart_rx_pin uart_ctx_pin uart_rts_pin tx_control_pin rx_control_pin
-xxx- -xxx- -xxx- -xxx- -xxx- -xxx- -xxx- -xxx- -xxx- -xxx- -xxx- -xxx- -xxx- -xxx- -xxx- -xxx-
PLATFORM_ESP32 ESP32-SDIO 0xfcfc 1 1 1 1 13 CN -1 -1 -1 -1 -1 -1 -1

2. Set Makefile

Open the Makefile and set to the new platform. Please use capital letters.

export ESP_AT_PROJECT_PLATFORM ?= PLATFORM_ESP32
export ESP_AT_MODULE_NAME ?= ESP32-SDIO

3. Configure the New Platform

  • 3.1. Enter module_config folder, copy the module_esp32_default to make a new module_esp32-sdio.

  • 3.2. In this example, we need not to change the partition table and the ESP-IDF version, so the at_customize.csv, IDF_VERSION and partitions_at.csv all need not to be changed.

  • 3.3. Revise the sdkconfig.defaults

    • Configure to use the partition table in the module_esp32-sdio folder, revise the following items：
     CONFIG_PARTITION_TABLE_CUSTOM_FILENAME="module_config/module_esp32-sdio/partitions_at.csv"

 CONFIG_PARTITION_TABLE_FILENAME="module_config/module_esp32-sdio/partitions_at.csv"

 CONFIG_AT_CUSTOMIZED_PARTITION_TABLE_FILE="module_config/module_esp32-sdio/at_customize.csv"

    • Since the esp-at project already supports the SDIO configuration, we only need to add it into the sdkconfig.defaults.

      • Remove the UART AT configuration in the sdkconfig.defaults.
       CONFIG_AT_BASE_ON_UART=y
 CONFIG_AT_UART_PORT=1
 CONFIG_AT_UART_PORT_RX_PIN=16
 CONFIG_AT_UART_PORT_TX_PIN=17
 CONFIG_AT_UART_PORT_RTS_PIN=14
 CONFIG_AT_UART_PORT_CTS_PIN=15

      And add the following configuration.

       CONFIG_AT_BASE_ON_SDIO=y

4. Revise the at_core lib

Since the ESP32 SDIO AT and the ESP32 UART AT are based on the same platform, ESP32, they will share the same at_core.lib. In this case, we need not to add any new at_core lib.
If you need to use a new at_core lib, put the lib into the components/at/lib, rename the lib as libxxxx_at_core.a, xxxx is the platform name. For example, if you set the ESP_AT_PROJECT_PLATFORM ?= PLATFORM_ESP8848 in the Makefile in Step 2, then the lib should be named as libesp8848_at_core.a.

如何增加一个新的平台支持

简介

当前工程根据不同的模组采用了不同的配置方式，具体配置信息在 module_config 目录下，如果未指定对应的模组配置信息，将采用平台默认的配置信息，现在已支持 esp32 和 esp8266 平台。工程默认为 PLATFORM_ESP32 平台的 WROOM-32 模组。 对于同款芯片不同通讯接口的模组，由于在 esp-at 中编译的代码不同，我们不能采用默认的 module_espxxxx_default 配置。

假设新的平台为 ESP32 SDIO AT，我们需要使用 SDIO 作为通讯介质，我们以此为例，进行阐述如何添加新的平台设备。

1. 创建模块信息

假设平台名称为 PLATFORM_ESP32，模块名称为 WROOM32-SDIO，打开 components/customized_partitions/raw_data/factory_param/factory_param_data.csv,按照标题

platform module_name magic_flag version module_id tx_max_power start_channel channel_num country_code uart_baudrate uart_tx_pin uart_rx_pin uart_ctx_pin uart_rts_pin tx_control_pin rx_control_pin

在最后添加

PLATFORM_ESP32 WROOM32-SDIO 0xfcfc 1 1 1 1 13 CN -1 -1 -1 -1 -1 -1 -1

2. 修改工程模块信息

打开 Makefile，修改平台名称和模块名称，对于英文字母，请使用大写格式

export ESP_AT_PROJECT_PLATFORM ?= PLATFORM_ESP32
export ESP_AT_MODULE_NAME ?= WROOM32-SDIO

**

3. 创建平台相关的配置

  • 3.1 进入 module_config, 将同款芯片的默认配置 module_esp32_default 拷贝一份为 module_esp32-sdio

  • 3.2 此处我们不需要修改 partition 分区表和 IDF 版本，所以 at_customize.csv、IDF_VERSION 和 partitions_at.csv 都不做修改

  • 3.3 修改 sdkconfig.defaults 文件

    • 配置使用 module_esp32-sdio 目录下的分区表文件，需要修改如下配置：
     CONFIG_PARTITION_TABLE_CUSTOM_FILENAME="module_config/module_esp32-sdio/partitions_at.csv"

 CONFIG_PARTITION_TABLE_FILENAME="module_config/module_esp32-sdio/partitions_at.csv"

 CONFIG_AT_CUSTOMIZED_PARTITION_TABLE_FILE="module_config/module_esp32-sdio/at_customize.csv"

    • 使用 sdio 配置，由于工程中已经包含选择 sdio 的配置，所以我们只需要将选择 sdio 的配置加入到 sdkconfig.defaults 文件即可

      • 移除 UART AT 相关配置
       CONFIG_AT_BASE_ON_UART=y

      并新增

       CONFIG_AT_BASE_ON_SDIO=y

4. 修改链接的库文件

由于 ESP32 SDIO AT 和 ESP32 UART AT 是同一个平台，使用的是相同的 at core 库，所以我们不需要再新增库文件。 若需要使用新的 lib, 则将 lib 复制到 components/at/lib 目录下,并将 lib 命名为 libxxxx_at_core.a, 其中 xxxx 为平台名称。假如根目录下的 Makefile �设置的 ESP_AT_PROJECT_PLATFORM ?= PLATFORM_ESP8848，那么库的名称就要命名为 libesp8848_at_core.a。