usb_device_cdc.c

// Based on usb_device_cdc.c from the MLA with added support for multiple ports.
// Source version: mla_v2016_11_07
// https://github.com/jimmo/numato-mimas-v2-pic-firmware/

// DOM-IGNORE-BEGIN
/*******************************************************************************
Copyright 2015 Microchip Technology Inc. (www.microchip.com)

Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at

    http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.

To request to license the code under the MLA license (www.microchip.com/mla_license),
please contact mla_licensing@microchip.com
*******************************************************************************/
//DOM-IGNORE-END

#include "system.h"
#include "usb.h"
#include "usb_device_cdc.h"

#ifdef USB_USE_CDC

// Store USB tx/rf buffers in region 0x0280 - 0x02ff
// See http://ww1.microchip.com/downloads/en/DeviceDoc/40001350F.pdf section 22.3
// The "usb_data" section is defined in the linker command line options.
#if CDC_NUM_PORTS >= 1
volatile unsigned char __section("usb_data") cdc1_data_tx[CDC1_DATA_IN_EP_SIZE];
volatile unsigned char __section("usb_data") cdc1_data_rx[CDC1_DATA_OUT_EP_SIZE];
#endif
#if CDC_NUM_PORTS >= 2
volatile unsigned char __section("usb_data") cdc2_data_tx[CDC2_DATA_IN_EP_SIZE];
volatile unsigned char __section("usb_data") cdc2_data_rx[CDC2_DATA_OUT_EP_SIZE];
#endif

CDC_PORT_STATE cdc_ports[CDC_NUM_PORTS];

/**************************************************************************
  SEND_ENCAPSULATED_COMMAND and GET_ENCAPSULATED_RESPONSE are required
  requests according to the CDC specification.
  However, it is not really being used here, therefore a dummy buffer is
  used for conformance.
 **************************************************************************/
#define dummy_length    0x08
uint8_t dummy_encapsulated_cmd_response[dummy_length];

#if defined(USB_CDC_SET_LINE_CODING_HANDLER)
CTRL_TRF_RETURN USB_CDC_SET_LINE_CODING_HANDLER(CTRL_TRF_PARAMS);
#endif

/** P R I V A T E  P R O T O T Y P E S ***************************************/
void USBCDCSetLineCoding(uint8_t cdc_port);

/** D E C L A R A T I O N S **************************************************/
//#pragma code

/** C L A S S  S P E C I F I C  R E Q ****************************************/
/******************************************************************************
 	Function:
 		void USBCheckCDCRequest(void)

 	Description:
 		This routine checks the most recently received SETUP data packet to
 		see if the request is specific to the CDC class.  If the request was
 		a CDC specific request, this function will take care of handling the
 		request and responding appropriately.

 	PreCondition:
 		This function should only be called after a control transfer SETUP
 		packet has arrived from the host.

	Parameters:
		None

	Return Values:
		None

	Remarks:
		This function does not change status or do anything if the SETUP packet
		did not contain a CDC class specific request.
  *****************************************************************************/
void USBCheckCDCRequest()
{
    /*
     * If request recipient is not an interface then return
     */
    if(SetupPkt.Recipient != USB_SETUP_RECIPIENT_INTERFACE_BITFIELD) return;

    /*
     * If request type is not class-specific then return
     */
    if(SetupPkt.RequestType != USB_SETUP_TYPE_CLASS_BITFIELD) return;

    for (uint8_t cdc_port = 0; cdc_port < CDC_NUM_PORTS; ++cdc_port) {
        /*
         * Interface ID must match interface numbers associated with
         * CDC class, else return
         */
        if((SetupPkt.bIntfID != cdc_ports[cdc_port].if_comm) &&
           (SetupPkt.bIntfID != cdc_ports[cdc_port].if_data)) continue;

        switch(SetupPkt.bRequest)
        {
            //****** These commands are required ******//
            case SEND_ENCAPSULATED_COMMAND:
             //send the packet
                inPipes[0].pSrc.bRam = (uint8_t*)dummy_encapsulated_cmd_response;
                inPipes[0].wCount.Val = dummy_length;
                inPipes[0].info.bits.ctrl_trf_mem = USB_EP0_RAM;
                inPipes[0].info.bits.busy = 1;
                break;
            case GET_ENCAPSULATED_RESPONSE:
                // Populate dummy_encapsulated_cmd_response first.
                inPipes[0].pSrc.bRam = (uint8_t*)dummy_encapsulated_cmd_response;
                inPipes[0].info.bits.busy = 1;
                break;
            //****** End of required commands ******//

            #if defined(USB_CDC_SUPPORT_ABSTRACT_CONTROL_MANAGEMENT_CAPABILITIES_D1)
            case SET_LINE_CODING:
                outPipes[0].wCount.Val = SetupPkt.wLength;
                outPipes[0].pDst.bRam = (uint8_t*)LINE_CODING_TARGET;
                outPipes[0].pFunc = LINE_CODING_PFUNC;
                outPipes[0].info.bits.busy = 1;
                break;

            case GET_LINE_CODING:
                USBEP0SendRAMPtr(
                    (uint8_t*)&cdc_ports[cdc_port].line_coding,
                    LINE_CODING_LENGTH,
                    USB_EP0_INCLUDE_ZERO);
                break;

            case SET_CONTROL_LINE_STATE:
                cdc_ports[cdc_port].control_signal_bitmap._byte = (uint8_t)SetupPkt.wValue;
                //------------------------------------------------------------------
                //One way to control the RTS pin is to allow the USB host to decide the value
                //that should be output on the RTS pin.  Although RTS and CTS pin functions
                //are technically intended for UART hardware based flow control, some legacy
                //UART devices use the RTS pin like a "general purpose" output pin
                //from the PC host.  In this usage model, the RTS pin is not related
                //to flow control for RX/TX.
                //In this scenario, the USB host would want to be able to control the RTS
                //pin, and the below line of code should be uncommented.
                //However, if the intention is to implement true RTS/CTS flow control
                //for the RX/TX pair, then this application firmware should override
                //the USB host's setting for RTS, and instead generate a real RTS signal,
                //based on the amount of remaining buffer space available for the
                //actual hardware UART of this microcontroller.  In this case, the
                //below code should be left commented out, but instead RTS should be
                //controlled in the application firmware responsible for operating the
                //hardware UART of this microcontroller.
                //---------
                //CONFIGURE_RTS(cdc_ports[cdc_port].control_signal_bitmap.CARRIER_CONTROL);
                //------------------------------------------------------------------

                #if defined(USB_CDC_SUPPORT_DTR_SIGNALING)
                    if(cdc_ports[cdc_port].control_signal_bitmap.DTE_PRESENT == 1)
                    {
                        UART_DTR = USB_CDC_DTR_ACTIVE_LEVEL;
                    }
                    else
                    {
                        UART_DTR = (USB_CDC_DTR_ACTIVE_LEVEL ^ 1);
                    }
                #endif
                inPipes[0].info.bits.busy = 1;
                break;
            #endif

            #if defined(USB_CDC_SUPPORT_ABSTRACT_CONTROL_MANAGEMENT_CAPABILITIES_D2)
            case SEND_BREAK:                        // Optional
                inPipes[0].info.bits.busy = 1;
                if (SetupPkt.wValue == 0xFFFF)  //0xFFFF means send break indefinitely until a new SEND_BREAK command is received
                {
                    UART_Tx = 0;       // Prepare to drive TX low (for break signaling)
                    UART_TRISTx = 0;   // Make sure TX pin configured as an output
                    UART_ENABLE = 0;   // Turn off USART (to relinquish TX pin control)
                }
                else if (SetupPkt.wValue == 0x0000) //0x0000 means stop sending indefinite break
                {
                    UART_ENABLE = 1;   // turn on USART
                    UART_TRISTx = 1;   // Make TX pin an input
                }
                else
                {
                    //Send break signaling on the pin for (SetupPkt.wValue) milliseconds
                    UART_SEND_BREAK();
                }
                break;
            #endif
            default:
                break;
        }//end switch(SetupPkt.bRequest)
    }
}//end USBCheckCDCRequest

/** U S E R  A P I ***********************************************************/

/**************************************************************************
  Function:
        void CDCInitEP(void)

  Summary:
    This function initializes the CDC function driver. This function should
    be called after the SET_CONFIGURATION command (ex: within the context of
    the USBCBInitEP() function).
  Description:
    This function initializes the CDC function driver. This function sets
    the default line coding (baud rate, bit parity, number of data bits,
    and format). This function also enables the endpoints and prepares for
    the first transfer from the host.

    This function should be called after the SET_CONFIGURATION command.
    This is most simply done by calling this function from the
    USBCBInitEP() function.

    Typical Usage:
    <code>
        void USBCBInitEP(void)
        {
            CDCInitEP();
        }
    </code>
  Conditions:
    None
  Remarks:
    None
  **************************************************************************/
void CDCInitEP(uint8_t cdc_port, uint8_t if_comm, uint8_t ep_comm, uint8_t if_data, uint8_t ep_data)
{
    cdc_ports[cdc_port].if_comm = if_comm;
    cdc_ports[cdc_port].ep_comm = ep_comm;
    cdc_ports[cdc_port].if_data = if_data;
    cdc_ports[cdc_port].ep_data = ep_data;

    if (cdc_port == 0) {
        cdc_ports[cdc_port].cdc_data_tx = cdc1_data_tx;
        cdc_ports[cdc_port].cdc_data_rx = cdc1_data_rx;
        cdc_ports[cdc_port].ep_out_size = CDC1_DATA_OUT_EP_SIZE;
        cdc_ports[cdc_port].ep_in_size = CDC1_DATA_IN_EP_SIZE;
    }
#if CDC_NUM_PORTS >= 2
    else if (cdc_port == 1) {
        cdc_ports[cdc_port].cdc_data_tx = cdc2_data_tx;
        cdc_ports[cdc_port].cdc_data_rx = cdc2_data_rx;
        cdc_ports[cdc_port].ep_out_size = CDC2_DATA_OUT_EP_SIZE;
        cdc_ports[cdc_port].ep_in_size = CDC2_DATA_IN_EP_SIZE;
    }
#endif

    //Abstract line coding information
    cdc_ports[cdc_port].line_coding.dwDTERate   = 19200;      // baud rate
    cdc_ports[cdc_port].line_coding.bCharFormat = 0x00;      // 1 stop bit
    cdc_ports[cdc_port].line_coding.bParityType = 0x00;      // None
    cdc_ports[cdc_port].line_coding.bDataBits = 0x08;        // 5,6,7,8, or 16

    cdc_ports[cdc_port].cdc_rx_len = 0;

    /*
     * Do not have to init Cnt of IN pipes here.
     * Reason:  Number of BYTEs to send to the host
     *          varies from one transaction to
     *          another. Cnt should equal the exact
     *          number of BYTEs to transmit for
     *          a given IN transaction.
     *          This number of BYTEs will only
     *          be known right before the data is
     *          sent.
     */
    USBEnableEndpoint(ep_comm,USB_IN_ENABLED|USB_HANDSHAKE_ENABLED|USB_DISALLOW_SETUP);
    USBEnableEndpoint(ep_data,USB_IN_ENABLED|USB_OUT_ENABLED|USB_HANDSHAKE_ENABLED|USB_DISALLOW_SETUP);

    cdc_ports[cdc_port].CDCDataOutHandle = USBRxOnePacket(ep_data,(uint8_t*)cdc_ports[cdc_port].cdc_data_rx,cdc_ports[cdc_port].ep_out_size);
    cdc_ports[cdc_port].CDCDataInHandle = NULL;

    #if defined(USB_CDC_SUPPORT_DSR_REPORTING)
      	CDCNotificationInHandle = NULL;
        mInitDTSPin();  //Configure DTS as a digital input
      	SerialStateBitmap.byte = 0x00;
      	OldSerialStateBitmap.byte = !SerialStateBitmap.byte;    //To force firmware to send an initial serial state packet to the host.
        //Prepare a SerialState notification element packet (contains info like DSR state)
        SerialStatePacket.bmRequestType = 0xA1; //Always 0xA1 for this type of packet.
        SerialStatePacket.bNotification = SERIAL_STATE;
        SerialStatePacket.wValue = 0x0000;  //Always 0x0000 for this type of packet
        SerialStatePacket.wIndex = cdc_ports[cdc_port].if_comm;  //Interface number
        SerialStatePacket.SerialState.byte = 0x00;
        SerialStatePacket.Reserved = 0x00;
        SerialStatePacket.wLength = 0x02;   //Always 2 bytes for this type of packet
        CDCNotificationHandler();
  	#endif

  	#if defined(USB_CDC_SUPPORT_DTR_SIGNALING)
  	    mInitDTRPin();
  	#endif

  	#if defined(USB_CDC_SUPPORT_HARDWARE_FLOW_CONTROL)
  	    mInitRTSPin();
  	    mInitCTSPin();
  	#endif

    cdc_ports[cdc_port].cdc_trf_state = CDC_TX_READY;
}//end CDCInitEP


/**************************************************************************
  Function: void CDCNotificationHandler(void)
  Summary: Checks for changes in DSR status and reports them to the USB host.
  Description: Checks for changes in DSR pin state and reports any changes
               to the USB host.
  Conditions: CDCInitEP() must have been called previously, prior to calling
              CDCNotificationHandler() for the first time.
  Remarks:
    This function is only implemented and needed when the
    USB_CDC_SUPPORT_DSR_REPORTING option has been enabled.  If the function is
    enabled, it should be called periodically to sample the DSR pin and feed
    the information to the USB host.  This can be done by calling
    CDCNotificationHandler() by itself, or, by calling CDCTxService() which
    also calls CDCNotificationHandler() internally, when appropriate.
  **************************************************************************/
#if defined(USB_CDC_SUPPORT_DSR_REPORTING)
void CDCNotificationHandler(uint8_t cdc_port)
{
    //Check the DTS I/O pin and if a state change is detected, notify the
    //USB host by sending a serial state notification element packet.
    if(UART_DTS == USB_CDC_DSR_ACTIVE_LEVEL) //UART_DTS must be defined to be an I/O pin in the hardware profile to use the DTS feature (ex: "PORTXbits.RXY")
    {
        SerialStateBitmap.bits.DSR = 1;
    }
    else
    {
        SerialStateBitmap.bits.DSR = 0;
    }

    //If the state has changed, and the endpoint is available, send a packet to
    //notify the hUSB host of the change.
    if((SerialStateBitmap.byte != OldSerialStateBitmap.byte) && (!USBHandleBusy(CDCNotificationInHandle)))
    {
        //Copy the updated value into the USB packet buffer to send.
        SerialStatePacket.SerialState.byte = SerialStateBitmap.byte;
        //We don't need to write to the other bytes in the SerialStatePacket USB
        //buffer, since they don't change and will always be the same as our
        //initialized value.

        //Send the packet over USB to the host.
        CDCNotificationInHandle = USBTransferOnePacket(CDC_COMM_EP, IN_TO_HOST, (uint8_t*)&SerialStatePacket, sizeof(SERIAL_STATE_NOTIFICATION));

        //Save the old value, so we can detect changes later.
        OldSerialStateBitmap.byte = SerialStateBitmap.byte;
    }
}//void CDCNotificationHandler(void)
#else
    #define CDCNotificationHandler(cdc_port) {}
#endif


/**********************************************************************************
  Function:
    bool USBCDCEventHandler(USB_EVENT event, void *pdata, uint16_t size)

  Summary:
    Handles events from the USB stack, which may have an effect on the CDC
    endpoint(s).

  Description:
    Handles events from the USB stack.  This function should be called when
    there is a USB event that needs to be processed by the CDC driver.

  Conditions:
    Value of input argument 'len' should be smaller than the maximum
    endpoint size responsible for receiving bulk data from USB host for CDC
    class. Input argument 'buffer' should point to a buffer area that is
    bigger or equal to the size specified by 'len'.
  Input:
    event - the type of event that occurred
    pdata - pointer to the data that caused the event
    size - the size of the data that is pointed to by pdata

  **********************************************************************************/
bool USBCDCEventHandler(USB_EVENT event, void *pdata, uint16_t size)
{
    if ((uint16_t)event == EVENT_TRANSFER_TERMINATED) {
        for (uint8_t cdc_port = 0; cdc_port < CDC_NUM_PORTS; ++cdc_port) {
            if(pdata == cdc_ports[cdc_port].CDCDataOutHandle)
            {
                cdc_ports[cdc_port].CDCDataOutHandle = USBRxOnePacket(cdc_ports[cdc_port].ep_data,(uint8_t*)cdc_ports[cdc_port].cdc_data_rx,cdc_ports[cdc_port].ep_out_size);
            }
            if(pdata == cdc_ports[cdc_port].CDCDataInHandle)
            {
                //flush all of the data in the CDC buffer
                cdc_ports[cdc_port].cdc_trf_state = CDC_TX_READY;
                cdc_ports[cdc_port].cdc_tx_len = 0;
            }
        }
        return true;
    }
    return false;
}

/**********************************************************************************
  Function:
        uint8_t getsUSBUSART(char *buffer, uint8_t len)

  Summary:
    getsUSBUSART copies a string of BYTEs received through USB CDC Bulk OUT
    endpoint to a user's specified location. It is a non-blocking function.
    It does not wait for data if there is no data available. Instead it
    returns '0' to notify the caller that there is no data available.

  Description:
    getsUSBUSART copies a string of BYTEs received through USB CDC Bulk OUT
    endpoint to a user's specified location. It is a non-blocking function.
    It does not wait for data if there is no data available. Instead it
    returns '0' to notify the caller that there is no data available.

    Typical Usage:
    <code>
        uint8_t numBytes;
        uint8_t buffer[64]

        numBytes = getsUSBUSART(buffer,sizeof(buffer)); //until the buffer is free.
        if(numBytes \> 0)
        {
            //we received numBytes bytes of data and they are copied into
            //  the "buffer" variable.  We can do something with the data
            //  here.
        }
    </code>
  Conditions:
    Value of input argument 'len' should be smaller than the maximum
    endpoint size responsible for receiving bulk data from USB host for CDC
    class. Input argument 'buffer' should point to a buffer area that is
    bigger or equal to the size specified by 'len'.
  Input:
    buffer -  Pointer to where received BYTEs are to be stored
    len -     The number of BYTEs expected.

  **********************************************************************************/
uint8_t getsUSBUSART(uint8_t cdc_port, uint8_t *buffer, uint8_t len)
{
    cdc_ports[cdc_port].cdc_rx_len = 0;

    if(!USBHandleBusy(cdc_ports[cdc_port].CDCDataOutHandle))
    {
        /*
         * Adjust the expected number of BYTEs to equal
         * the actual number of BYTEs received.
         */
        if(len > USBHandleGetLength(cdc_ports[cdc_port].CDCDataOutHandle))
            len = USBHandleGetLength(cdc_ports[cdc_port].CDCDataOutHandle);

        /*
         * Copy data from dual-ram buffer to user's buffer
         */
        for(cdc_ports[cdc_port].cdc_rx_len = 0; cdc_ports[cdc_port].cdc_rx_len < len; cdc_ports[cdc_port].cdc_rx_len++)
            buffer[cdc_ports[cdc_port].cdc_rx_len] = cdc_ports[cdc_port].cdc_data_rx[cdc_ports[cdc_port].cdc_rx_len];

        /*
         * Prepare dual-ram buffer for next OUT transaction
         */

        cdc_ports[cdc_port].CDCDataOutHandle = USBRxOnePacket(cdc_ports[cdc_port].ep_data,(uint8_t*)cdc_ports[cdc_port].cdc_data_rx,cdc_ports[cdc_port].ep_out_size);

    }//end if

    return cdc_ports[cdc_port].cdc_rx_len;

}//end getsUSBUSART

/******************************************************************************
  Function:
	void putUSBUSART(char *data, uint8_t length)

  Summary:
    putUSBUSART writes an array of data to the USB. Use this version, is
    capable of transferring 0x00 (what is typically a NULL character in any of
    the string transfer functions).

  Description:
    putUSBUSART writes an array of data to the USB. Use this version, is
    capable of transferring 0x00 (what is typically a NULL character in any of
    the string transfer functions).

    Typical Usage:
    <code>
        if(USBUSARTIsTxTrfReady())
        {
            char data[] = {0x00, 0x01, 0x02, 0x03, 0x04};
            putUSBUSART(data,5);
        }
    </code>

    The transfer mechanism for device-to-host(put) is more flexible than
    host-to-device(get). It can handle a string of data larger than the
    maximum size of bulk IN endpoint. A state machine is used to transfer a
    \long string of data over multiple USB transactions. CDCTxService()
    must be called periodically to keep sending blocks of data to the host.

  Conditions:
    USBUSARTIsTxTrfReady() must return true. This indicates that the last
    transfer is complete and is ready to receive a new block of data. The
    string of characters pointed to by 'data' must equal to or smaller than
    255 BYTEs.

  Input:
    char *data - pointer to a RAM array of data to be transfered to the host
    uint8_t length - the number of bytes to be transfered (must be less than 255).

 *****************************************************************************/
void putUSBUSART(uint8_t cdc_port, uint8_t *data, uint8_t  length)
{
    /*
     * User should have checked that cdc_ports[cdc_port].cdc_trf_state is in CDC_TX_READY state
     * before calling this function.
     * As a safety precaution, this function checks the state one more time
     * to make sure it does not override any pending transactions.
     *
     * Currently it just quits the routine without reporting any errors back
     * to the user.
     *
     * Bottom line: User MUST make sure that USBUSARTIsTxTrfReady()==1
     *             before calling this function!
     * Example:
     * if(USBUSARTIsTxTrfReady())
     *     putUSBUSART(pData, Length);
     *
     * IMPORTANT: Never use the following blocking while loop to wait:
     * while(!USBUSARTIsTxTrfReady())
     *     putUSBUSART(pData, Length);
     *
     * The whole firmware framework is written based on cooperative
     * multi-tasking and a blocking code is not acceptable.
     * Use a state machine instead.
     */
    USBMaskInterrupts();
    if(cdc_ports[cdc_port].cdc_trf_state == CDC_TX_READY)
    {
        mUSBUSARTTxRam(cdc_port, (uint8_t*)data, length);     // See cdc.h
    }
    USBUnmaskInterrupts();
}//end putUSBUSART

/******************************************************************************
	Function:
		void putsUSBUSART(char *data)

  Summary:
    putsUSBUSART writes a string of data to the USB including the null
    character. Use this version, 'puts', to transfer data from a RAM buffer.

  Description:
    putsUSBUSART writes a string of data to the USB including the null
    character. Use this version, 'puts', to transfer data from a RAM buffer.

    Typical Usage:
    <code>
        if(USBUSARTIsTxTrfReady())
        {
            char data[] = "Hello World";
            putsUSBUSART(data);
        }
    </code>

    The transfer mechanism for device-to-host(put) is more flexible than
    host-to-device(get). It can handle a string of data larger than the
    maximum size of bulk IN endpoint. A state machine is used to transfer a
    \long string of data over multiple USB transactions. CDCTxService()
    must be called periodically to keep sending blocks of data to the host.

  Conditions:
    USBUSARTIsTxTrfReady() must return true. This indicates that the last
    transfer is complete and is ready to receive a new block of data. The
    string of characters pointed to by 'data' must equal to or smaller than
    255 BYTEs.

  Input:
    char *data -  null\-terminated string of constant data. If a
                            null character is not found, 255 BYTEs of data
                            will be transferred to the host.

 *****************************************************************************/

void putsUSBUSART(uint8_t cdc_port, char *data)
{
    uint8_t len;
    char *pData;

    /*
     * User should have checked that cdc_ports[cdc_port].cdc_trf_state is in CDC_TX_READY state
     * before calling this function.
     * As a safety precaution, this function checks the state one more time
     * to make sure it does not override any pending transactions.
     *
     * Currently it just quits the routine without reporting any errors back
     * to the user.
     *
     * Bottom line: User MUST make sure that USBUSARTIsTxTrfReady()==1
     *             before calling this function!
     * Example:
     * if(USBUSARTIsTxTrfReady())
     *     putsUSBUSART(pData, Length);
     *
     * IMPORTANT: Never use the following blocking while loop to wait:
     * while(!USBUSARTIsTxTrfReady())
     *     putsUSBUSART(pData);
     *
     * The whole firmware framework is written based on cooperative
     * multi-tasking and a blocking code is not acceptable.
     * Use a state machine instead.
     */
    USBMaskInterrupts();
    if(cdc_ports[cdc_port].cdc_trf_state != CDC_TX_READY)
    {
        USBUnmaskInterrupts();
        return;
    }

    /*
     * While loop counts the number of BYTEs to send including the
     * null character.
     */
    len = 0;
    pData = data;
    do
    {
        len++;
        if(len == 255) break;       // Break loop once max len is reached.
    }while(*pData++);

    /*
     * Second piece of information (length of data to send) is ready.
     * Call mUSBUSARTTxRam to setup the transfer.
     * The actual transfer process will be handled by CDCTxService(),
     * which should be called once per Main Program loop.
     */
    mUSBUSARTTxRam(cdc_port, (uint8_t*)data, len);     // See cdc.h
    USBUnmaskInterrupts();
}//end putsUSBUSART

/**************************************************************************
  Function:
        void putrsUSBUSART(const const char *data)

  Summary:
    putrsUSBUSART writes a string of data to the USB including the null
    character. Use this version, 'putrs', to transfer data literals and
    data located in program memory.

  Description:
    putrsUSBUSART writes a string of data to the USB including the null
    character. Use this version, 'putrs', to transfer data literals and
    data located in program memory.

    Typical Usage:
    <code>
        if(USBUSARTIsTxTrfReady())
        {
            putrsUSBUSART("Hello World");
        }
    </code>

    The transfer mechanism for device-to-host(put) is more flexible than
    host-to-device(get). It can handle a string of data larger than the
    maximum size of bulk IN endpoint. A state machine is used to transfer a
    \long string of data over multiple USB transactions. CDCTxService()
    must be called periodically to keep sending blocks of data to the host.

  Conditions:
    USBUSARTIsTxTrfReady() must return true. This indicates that the last
    transfer is complete and is ready to receive a new block of data. The
    string of characters pointed to by 'data' must equal to or smaller than
    255 BYTEs.

  Input:
    const const char *data -  null\-terminated string of constant data. If a
                            null character is not found, 255 uint8_ts of data
                            will be transferred to the host.

  **************************************************************************/
void putrsUSBUSART(uint8_t cdc_port, const const char *data)
{
    uint8_t len;
    const const char *pData;

    /*
     * User should have checked that cdc_ports[cdc_port].cdc_trf_state is in CDC_TX_READY state
     * before calling this function.
     * As a safety precaution, this function checks the state one more time
     * to make sure it does not override any pending transactions.
     *
     * Currently it just quits the routine without reporting any errors back
     * to the user.
     *
     * Bottom line: User MUST make sure that USBUSARTIsTxTrfReady()
     *             before calling this function!
     * Example:
     * if(USBUSARTIsTxTrfReady())
     *     putsUSBUSART(pData);
     *
     * IMPORTANT: Never use the following blocking while loop to wait:
     * while(cdc_ports[cdc_port].cdc_trf_state != CDC_TX_READY)
     *     putsUSBUSART(pData);
     *
     * The whole firmware framework is written based on cooperative
     * multi-tasking and a blocking code is not acceptable.
     * Use a state machine instead.
     */
    USBMaskInterrupts();
    if(cdc_ports[cdc_port].cdc_trf_state != CDC_TX_READY)
    {
        USBUnmaskInterrupts();
        return;
    }

    /*
     * While loop counts the number of BYTEs to send including the
     * null character.
     */
    len = 0;
    pData = data;
    do
    {
        len++;
        if(len == 255) break;       // Break loop once max len is reached.
    }while(*pData++);

    /*
     * Second piece of information (length of data to send) is ready.
     * Call mUSBUSARTTxRom to setup the transfer.
     * The actual transfer process will be handled by CDCTxService(),
     * which should be called once per Main Program loop.
     */

    mUSBUSARTTxRom(cdc_port, (const uint8_t*)data,len); // See cdc.h
    USBUnmaskInterrupts();

}//end putrsUSBUSART

/************************************************************************
  Function:
        void CDCTxService(void)

  Summary:
    CDCTxService handles device-to-host transaction(s). This function
    should be called once per Main Program loop after the device reaches
    the configured state.
  Description:
    CDCTxService handles device-to-host transaction(s). This function
    should be called once per Main Program loop after the device reaches
    the configured state (after the CDCIniEP() function has already executed).
    This function is needed, in order to advance the internal software state
    machine that takes care of sending multiple transactions worth of IN USB
    data to the host, associated with CDC serial data.  Failure to call
    CDCTxService() periodically will prevent data from being sent to the
    USB host, over the CDC serial data interface.

    Typical Usage:
    <code>
    void main(void)
    {
        USBDeviceInit();
        while(1)
        {
            USBDeviceTasks();
            if((USBGetDeviceState() \< CONFIGURED_STATE) ||
               (USBIsDeviceSuspended() == true))
            {
                //Either the device is not configured or we are suspended
                //  so we don't want to do execute any application code
                continue;   //go back to the top of the while loop
            }
            else
            {
                //Keep trying to send data to the PC as required
                CDCTxService();

                //Run application code.
                UserApplication();
            }
        }
    }
    </code>
  Conditions:
    CDCIniEP() function should have already executed/the device should be
    in the CONFIGURED_STATE.
  Remarks:
    None
  ************************************************************************/

void CDCTxService()
{
    USBMaskInterrupts();

    for (uint8_t cdc_port = 0; cdc_port < CDC_NUM_PORTS; ++cdc_port) {
        uint8_t byte_to_send;
        uint8_t i;

        CDCNotificationHandler(cdc_port);

        if(USBHandleBusy(cdc_ports[cdc_port].CDCDataInHandle))
        {
            continue;
        }

        /*
         * Completing stage is necessary while [ mCDCUSartTxIsBusy()==1 ].
         * By having this stage, user can always check cdc_ports[cdc_port].cdc_trf_state,
         * and not having to call mCDCUsartTxIsBusy() directly.
         */
        if(cdc_ports[cdc_port].cdc_trf_state == CDC_TX_COMPLETING)
            cdc_ports[cdc_port].cdc_trf_state = CDC_TX_READY;

        /*
         * If CDC_TX_READY state, nothing to do, just return.
         */
        if(cdc_ports[cdc_port].cdc_trf_state == CDC_TX_READY)
        {
            continue;
        }

        /*
         * If CDC_TX_BUSY_ZLP state, send zero length packet
         */
        if(cdc_ports[cdc_port].cdc_trf_state == CDC_TX_BUSY_ZLP)
        {
            cdc_ports[cdc_port].CDCDataInHandle = USBTxOnePacket(cdc_ports[cdc_port].ep_data,NULL,0);
            //CDC_DATA_BD_IN.CNT = 0;
            cdc_ports[cdc_port].cdc_trf_state = CDC_TX_COMPLETING;
        }
        else if(cdc_ports[cdc_port].cdc_trf_state == CDC_TX_BUSY)
        {
            /*
             * First, have to figure out how many byte of data to send.
             */
            if(cdc_ports[cdc_port].cdc_tx_len > cdc_ports[cdc_port].ep_in_size)
                byte_to_send = cdc_ports[cdc_port].ep_in_size;
            else
                byte_to_send = cdc_ports[cdc_port].cdc_tx_len;

            /*
             * Subtract the number of bytes just about to be sent from the total.
             */
            cdc_ports[cdc_port].cdc_tx_len = cdc_ports[cdc_port].cdc_tx_len - byte_to_send;

            cdc_ports[cdc_port].pCDCDst.bRam = (uint8_t*)cdc_ports[cdc_port].cdc_data_tx; // Set destination pointer

            i = byte_to_send;
            if(cdc_ports[cdc_port].cdc_mem_type == USB_EP0_ROM)            // Determine type of memory source
            {
                while(i)
                {
                    *cdc_ports[cdc_port].pCDCDst.bRam = *cdc_ports[cdc_port].pCDCSrc.bRom;
                    cdc_ports[cdc_port].pCDCDst.bRam++;
                    cdc_ports[cdc_port].pCDCSrc.bRom++;
                    i--;
                }//end while(byte_to_send)
            }
            else
            {
                while(i)
                {
                    *cdc_ports[cdc_port].pCDCDst.bRam = *cdc_ports[cdc_port].pCDCSrc.bRam;
                    cdc_ports[cdc_port].pCDCDst.bRam++;
                    cdc_ports[cdc_port].pCDCSrc.bRam++;
                    i--;
                }
            }

            /*
             * Lastly, determine if a zero length packet state is necessary.
             * See explanation in USB Specification 2.0: Section 5.8.3
             */
            if(cdc_ports[cdc_port].cdc_tx_len == 0)
            {
                if(byte_to_send == cdc_ports[cdc_port].ep_in_size)
                    cdc_ports[cdc_port].cdc_trf_state = CDC_TX_BUSY_ZLP;
                else
                    cdc_ports[cdc_port].cdc_trf_state = CDC_TX_COMPLETING;
            }//end if(cdc_ports[cdc_port].cdc_tx_len...)
            cdc_ports[cdc_port].CDCDataInHandle = USBTxOnePacket(cdc_ports[cdc_port].ep_data,(uint8_t*)cdc_ports[cdc_port].cdc_data_tx,byte_to_send);

        }//end if(cdc_tx_sate == CDC_TX_BUSY)
    }

    USBUnmaskInterrupts();
}//end CDCTxService

#endif //USB_USE_CDC

/** EOF cdc.c ****************************************************************/