How do I edit coordinate increments in the data and corrections report tabs.

[phreekbird]

Yes, I scoured the Wiki. However, I didn't find it anywhere.

How do I get my data and corrections tabs (as shown in this screenshot: https://github.com/jneilliii/OctoPrint-BedLevelVisualizer/blob/master/wiki/index.md#data) to only show the cords like in that screenshot (separated by increments of 50 or 100)? Mine (and, by default, every install I have ever done) has all the coordinates separated by increments of 10. This puts so much info on the page that I cannot look at the visual representation of the wheel and which direction to turn it. If I could shrink the information (by only showing increments of, say, 50 or 100 or so), then I could see the four corners and the wheel turn info on the same page.

Your help is greatly appreciated, thanks.

[jneilliii]

Can you share a screenshot? It's based on how many points are returned by your firmware.

[phreekbird]

Please take a look at the highlighted sections. This is what I get. There is so much info here I cannot see all the information. If I scrolled down, I wouldn't be able to see the corrections wheel/circle on the top right.

[jneilliii]

weird, that's the largest quantity of probing points I've ever seen reported before. if you enable the option to display the corrections on the tab, does it show the whole table without going out of view under the graph? what firmware and version is your printer using and can you share the contents of the terminal tab at the end of the collection process so I can see the data overall?

[phreekbird]

It shows the whole table; it's never all in one view; I have to move everything around to see it. And I can never view the corrections wheel/circle if I'm looking at the bottom of the chart. Firmware is stock ender three max neo.

Not sure if this is the info you are requesting; however, please find the attached.
plugin_bedlevelvisualizer_debug.log

[jneilliii]

That helps a lot actually. Seems that your 5x5 probing grid is getting the CATMUL subdivision and reporting that. Which gcode commands are you using to collect the data. What is returned on the terminal tab when you send the command M420 V?

[phreekbird]

Send: M420 V
Recv: Bilinear Leveling Grid:
Recv:       0      1      2      3      4
Recv:  0 -0.184 -0.084 -0.054 -0.050 -0.104
Recv:  1 -0.067 +0.014 +0.040 +0.036 -0.054
Recv:  2 -0.082 -0.028 -0.014 -0.006 -0.102
Recv:  3 -0.051 -0.027 -0.032 -0.051 -0.128
Recv:  4 +0.001 -0.021 -0.061 -0.099 -0.184
Recv: 
Recv: Subdivided with CATMULL ROM Leveling Grid:
Recv:         0        1        2        3        4        5        6        7        8        9       10       11       12       13       14       15       16       17       18       19       20
Recv:  0 -0.18450 -0.16338 -0.14114 -0.11946 -0.10002 -0.08450 -0.07361 -0.06624 -0.06130 -0.05775 -0.05450 -0.05102 -0.04803 -0.04633 -0.04672 -0.05000 -0.05712 -0.06755 -0.07987 -0.09266 -0.10450
Recv:  1 -0.15888 -0.13854 -0.11713 -0.09625 -0.07752 -0.06255 -0.05199 -0.04475 -0.03988 -0.03640 -0.03333 -0.03008 -0.02728 -0.02585 -0.02670 -0.03075 -0.03903 -0.05092 -0.06489 -0.07937 -0.09282
Recv:  2 -0.13114 -0.11156 -0.09094 -0.07085 -0.05280 -0.03836 -0.02808 -0.02095 -0.01611 -0.01267 -0.00980 -0.00679 -0.00425 -0.00317 -0.00456 -0.00946 -0.01897 -0.03242 -0.04813 -0.06440 -0.07955
Recv:  3 -0.10446 -0.08564 -0.06585 -0.04654 -0.02919 -0.01528 -0.00532 +0.00169 +0.00649 +0.00986 +0.01256 +0.01532 +0.01765 +0.01841 +0.01651 +0.01082 +0.00011 -0.01486 -0.03226 -0.05028 -0.06707
Recv:  4 -0.08202 -0.06402 -0.04509 -0.02663 -0.01003 +0.00329 +0.01289 +0.01969 +0.02439 +0.02765 +0.03017 +0.03277 +0.03498 +0.03558 +0.03333 +0.02699 +0.01526 -0.00104 -0.01995 -0.03951 -0.05776
Recv:  5 -0.06700 -0.04991 -0.03194 -0.01440 +0.00135 +0.01400 +0.02312 +0.02959 +0.03405 +0.03714 +0.03950 +0.04204 +0.04434 +0.04502 +0.04270 +0.03600 +0.02354 +0.00623 -0.01385 -0.03462 -0.05400
Recv:  6 -0.06226 -0.04618 -0.02927 -0.01278 +0.00203 +0.01390 +0.02241 +0.02838 +0.03246 +0.03532 +0.03759 +0.04034 +0.04313 +0.04437 +0.04247 +0.03584 +0.02300 +0.00503 -0.01589 -0.03754 -0.05772
Recv:  7 -0.06567 -0.05069 -0.03493 -0.01956 -0.00577 +0.00525 +0.01304 +0.01838 +0.02198 +0.02455 +0.02680 +0.02999 +0.03362 +0.03584 +0.03478 +0.02856 +0.01563 -0.00277 -0.02430 -0.04661 -0.06735
Recv:  8 -0.07295 -0.05913 -0.04457 -0.03038 -0.01767 -0.00755 -0.00055 +0.00408 +0.00712 +0.00936 +0.01158 +0.01520 +0.01972 +0.02297 +0.02283 +0.01716 +0.00431 -0.01430 -0.03619 -0.05890 -0.07997
Recv:  9 -0.07982 -0.06719 -0.05386 -0.04088 -0.02928 -0.02010 -0.01392 -0.01002 -0.00758 -0.00574 -0.00367 +0.00020 +0.00531 +0.00931 +0.00987 +0.00464 -0.00806 -0.02667 -0.04867 -0.07151 -0.09266
Recv: 10 -0.08200 -0.07055 -0.05846 -0.04668 -0.03621 -0.02800 -0.02263 -0.01944 -0.01760 -0.01623 -0.01450 -0.01080 -0.00570 -0.00160 -0.00090 -0.00600 -0.01858 -0.03704 -0.05886 -0.08152 -0.10250
Recv: 11 -0.07907 -0.06878 -0.05787 -0.04727 -0.03789 -0.03063 -0.02603 -0.02346 -0.02216 -0.02132 -0.02015 -0.01716 -0.01286 -0.00952 -0.00939 -0.01475 -0.02718 -0.04516 -0.06633 -0.08829 -0.10866
Recv: 12 -0.07390 -0.06473 -0.05500 -0.04556 -0.03725 -0.03094 -0.02707 -0.02507 -0.02428 -0.02400 -0.02358 -0.02168 -0.01877 -0.01681 -0.01777 -0.02362 -0.03579 -0.05296 -0.07300 -0.09376 -0.11308
Recv: 13 -0.06708 -0.05910 -0.05058 -0.04233 -0.03514 -0.02982 -0.02674 -0.02535 -0.02512 -0.02549 -0.02592 -0.02534 -0.02410 -0.02383 -0.02612 -0.03260 -0.04451 -0.06077 -0.07952 -0.09889 -0.11702
Recv: 14 -0.05925 -0.05254 -0.04534 -0.03838 -0.03242 -0.02821 -0.02603 -0.02538 -0.02584 -0.02697 -0.02835 -0.02911 -0.02955 -0.03094 -0.03458 -0.04173 -0.05347 -0.06894 -0.08654 -0.10467 -0.12174
Recv: 15 -0.05100 -0.04574 -0.04001 -0.03451 -0.02994 -0.02700 -0.02592 -0.02624 -0.02760 -0.02964 -0.03200 -0.03397 -0.03578 -0.03852 -0.04323 -0.05100 -0.06276 -0.07779 -0.09469 -0.11206 -0.12850
Recv: 16 -0.04201 -0.03840 -0.03437 -0.03054 -0.02758 -0.02612 -0.02639 -0.02797 -0.03050 -0.03365 -0.03706 -0.04009 -0.04294 -0.04663 -0.05214 -0.06048 -0.07249 -0.08752 -0.10427 -0.12146 -0.13778
Recv: 17 -0.03188 -0.03010 -0.02792 -0.02595 -0.02476 -0.02496 -0.02679 -0.02985 -0.03377 -0.03820 -0.04277 -0.04682 -0.05058 -0.05505 -0.06124 -0.07015 -0.08259 -0.09790 -0.11484 -0.13220 -0.14874
Recv: 18 -0.02108 -0.02123 -0.02102 -0.02099 -0.02168 -0.02364 -0.02714 -0.03181 -0.03725 -0.04307 -0.04885 -0.05389 -0.05848 -0.06364 -0.07044 -0.07993 -0.09290 -0.10865 -0.12599 -0.14372 -0.16066
Recv: 19 -0.01013 -0.01223 -0.01400 -0.01594 -0.01853 -0.02228 -0.02748 -0.03380 -0.04079 -0.04801 -0.05502 -0.06106 -0.06644 -0.07228 -0.07967 -0.08974 -0.10326 -0.11949 -0.13727 -0.15543 -0.17282
Recv: 20 +0.00050 -0.00350 -0.00721 -0.01107 -0.01552 -0.02100 -0.02784 -0.03574 -0.04422 -0.05280 -0.06100 -0.06805 -0.07428 -0.08082 -0.08885 -0.09950 -0.11352 -0.13015 -0.14827 -0.16676 -0.18450
Recv: 
Recv: echo:Bed Leveling ON
Recv: echo:Fade Height 10.00
Recv: ok

I am using the bilinear commands as shown in the documentation: https://github.com/jneilliii/OctoPrint-BedLevelVisualizer/blob/master/wiki/gcode-examples.md#bilinear-bed-levelling

[jneilliii]

Thanks, I'll have to figure out a way to float the circle bit I guess. That 20x20 grid is definitely not something I had planned for.