-
Notifications
You must be signed in to change notification settings - Fork 2
/
ANTMAKER.TXT
1188 lines (642 loc) · 42.6 KB
/
ANTMAKER.TXT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
* * * * * * * * * * * * * * * *
* *
* A N T E N N A M A K E R *
* *
* Antenna Design Programs *
* *
* * * * * * * * * * * * * * * *
Copyright 1994, ALC Electronics
By: John K. Agrelius, KM6HG
Protected by Federal Copyright Laws
Permission granted for non-commercial use and distribution.
A N T E N N A M A K E R
=========================
The programs in this package are intended to assist the average
Amateur Radio Operator with the design and construction of some of the
most common antennas in use today. Several antennas have been built using
these programs and excellent results have been reported. Just read all the
documentation thoroughly and follow the instructions and you'll have the
personal satisfaction of building your own antennas.
We do recommend that you use other sources of information such as the
ARRL Handbook for Radio Amateurs, the ARRL Antenna Book, the VHF Handbook
for Radio Amateurs and All About Cubical Quads, just to mention a few.
Disclaimer
----------
ALC Electronics distributes freeware and shareware programs and data
files without charging a fee.
In no case do we intentionally violate any copyright request or
convention.
We remind the purchaser that in the case of shareware, author's
rights are important. If you continue to use a program you must abide by
an author's request for registration and fee payment. This supports and
encourages the author to improve existing software and develop new
software products.
ALC Electronics and it's distributors cannot assume liability or
responsibility for any loss or damage arising from the use of these
programs. This product is used with this understanding by user.
Warranty and Liability
----------------------
ALC Electronics does not warrant that the functions contained in
these programs will meet your requirements or that the operation of these
programs will be uninterrupted or error free.
In no case will ALC Electronics be held liable for damages direct,
indirect or incidental resulting from any defect or omission in the Users
Manual, the Disk, or any other related items and processes, including, but
not limited to, any loss of income, anticipated profit or other
consequential damages.
This statement of limited liability replaces all other warranties or
guarantees, expressed or implied, including warranties of merchantability
and fitness for any purpose. ALC Electronics neither assumes any other
warranty or liability nor authorizes any other person to assume any other
warranty or liability for it, in connection with the use of this product.
CONTENTS
========
Inverted Vee Antennas ...................... Page 1
Cubical Quad Antennas ...................... Page 3
Coax Antenna Traps ......................... Page 7
Inverted Vee Diagrams ...................... Page 9
Cubical Quad Diagrams ...................... Page 10
Coax Trap Diagrams ......................... Page 13
Other Shareware Programs ................... Page 14
I N V E R T E D V E E A N T E N N A S
=========================================
By: John K. Agrelius, KM6HG
The Inverted Vee Antenna (sometimes called a Drooping Dipole) is
basically a center fed dipole with the ends lower than the feed point. The
characteristic impedance of this antenna at the feed point will vary with
the height above ground, the apex angle and surrounding objects. It will
generally be close enough to 50 ohms that it can be fed directly with 50
ohm coax. The apex angle (at the feed point) should be somewhere between
90 degrees and 120 degrees with 110 degrees as a good starting point. It's
not too critical, just don't make it less than 90 degrees. Also, don't be
afraid to use dog legs near the ends of the antenna if you don't have
enough real estate. Just try to keep the feed point in the clear and as
high as possible. This will improve your radiation pattern and your
radiation angle.
Running the Program
-------------------
The program is quite simple to use. Just enter the Design Frequency
and the Height above ground. The Frequency will be used to calculate the
dimensions and the Height will be used to determine the approximate feed
point impedance for your antenna. When the calculations are done and the
dimensions are displayed you'll have 4 Choices:
#1 - This will Restart the Program.
#2 - This will Recalculate with a New Antenna Height.
#3 - This will Print the Design Specifications of your Antenna.
#4 - This will Quit the Program and Return to the Main Menu.
Building Your Antenna
---------------------
The support for the antenna should be made of wood, fiberglass, PVC
or some other non-metallic material. A 3 or 4 foot piece of PVC pipe on
top of a metal mast works OK. An all wooden mast would be better but isn't
very practical for high antennas. You can use a small piece of plexiglass,
maybe 3" X 5" X 1/4", at the feed point, attached to the PVC pipe for the
antenna connections. Just drill a 1/4" hole near each corner, at one end
of the plexiglass. This will be used for the legs of the antenna. You
should also drill a couple of holes in the middle of the plexiglass near
the other end to be used for mounting it to the mast. Strip the insulation
off the end of one leg of the enameled copper wire for about 6 inches. Run
about 4 inches of this end of the wire through one of the corner holes and
making a loop, wrap it back on itself and solder the connection. Do the
same with the other leg of the antenna. Refer to FIGURE 1.
Connections between the antenna and the coax are made at the solder
joint of each leg. Separate the shield from the center conductor of the 50
ohm coax for about 4 inches. Use some silicone glue to weather proof the
coax where the shield and center conductor separate. Solder the shield to
Page 1
one leg of the antenna and solder the center conductor to the other leg.
Refer to FIGURE 1. NOTE - A good quality current balun could be used in
place of the plexiglass to reduce feedline radiation.
One thing you need to keep in mind is that the 4 inches of coax and
shield become part of the antenna. This extra length was lost when you
looped each leg through the plexiglass so it should balance out. BUT be
sure that in the beginning you cut the legs about a foot or two LONGER
than they need to be. You'll need to adjust the length of the legs for the
lowest VSWR. You can always cut off the extra length when you're done.
When adjusting the antenna, be sure to add or subtract equal amounts from
each leg. Also, you'll need insulators for the ends of the antenna and to
support any dog legs. You can use plexiglass or some PVC pipe with a hole
drilled in each end.
One final note - A good quality Current Balun is the best way to
connect the antenna to your coaxial cable. It will improve the radiation
pattern and cut down on RF radiated by the feedline.
Antenna Adjustment
------------------
With the antenna in position, check the VSWR with your SRW Meter.
First take a reading at the Design Frequency and write it down. Now check
the reading above and below the Design Frequency. If the VSWR is Higher at
the Higher frequency then it's obviously resonant at a lower frequency, so
you need to shorten the ends of the antenna. When the antenna is
shortened, the resonant frequency will go up. Remember, you must shorten
the antenna by the same amount on each leg. If the VSWR is Higher at the
Lower frequency then you'll have to lengthen the antenna. Continue to
adjust the antenna until the VSWR is at it's lowest reading at the Design
Frequency. The Approximate VSWR on the printout is exactly that, so don't
rely on it to much. The antenna is influenced by Height above ground (and
who knows where that is), the Apex Angle, any Surrounding objects and
probably other things we don't even know about yet. If the VSWR is less
than 2:1 across the entire band then it should work fine.
Page 2
C U B I C A L Q U A D A N T E N N A S
=========================================
By: John K. Agrelius, KM6HG
The Cubical Quad Antenna is basically a directional beam antenna made
out of wire loops. The loops are usually square and are approximately one
wavelength long, with the reflector slightly larger and the director(s)
slightly smaller. It has more gain per element than a Yagi, it is less
susceptible to static noise and best of all the characteristic impedance
is close enough to 50 ohms that it can be feed directly with 50 ohm coax.
The major disadvantage is that it's pretty bulky for HF and quite a chore
to build. But, it's ideal for VHF. In fact, I'm using a 5 element Quad on
2 meters at my QTH. It has great gain, a good front to back ratio, it
covers the entire band and the VSWR is flat at the Design Frequency.
Running the Program
-------------------
The program is quite simple to use. Just enter the Design Frequency
and the Number of Elements. The Frequency will be used to calculate the
dimensions and the Number of Elements will be used to determine the
Theoretical Gain. When the calculations are done and the dimensions are
displayed you'll have 4 Choices:
#1 - This will Restart the Program.
#2 - This will Recalculate with a New Number of Elements.
#3 - This will Print the Design Specifications of your Antenna.
#4 - This will Quit the Program and Return to the Main Menu.
In the next few paragraphs I'll go through the process of building a
vertically polarized 4 element, 2 meter (146 MHz) Cubical Quad. It's not
difficult but the dimensions are critical and you need to take your time.
The same basic techniques apply to the other bands, the only difference
would be that the size of almost everything would change proportionally.
Building Your Antenna
---------------------
The support for the antenna should be made of wood, fiberglass, PVC
or some other non-metallic material. I used 2" X 2" pine for the boom and
1/2" wood dowel for the spreaders. The wire loops were made of number 18
enameled copper wire (for HF I would use number 12 copperweld). You'll
also need a couple of pieces of 1/8" plexiglass about 1" X 2", a couple of
muffler clamps that will fit your mast and a piece of aluminum tubing or
PVC pipe about 18" long. That's it..
Take the 2" X 2" pine and using the dimensions from the printout,
cut the boom. CAUTION - The dimensions are the MINIMUM length of the boom,
you'll have to add a little just to be safe. I added an additional 24"
because I mounted the boom to the mast behind the reflector so the antenna
Page 3
was not affected by the mast. This makes the total boom length about 64"
(40.2" + 24"). Now, take the wood dowel and using the dimensions from the
printout, cut two wood dowels per element. CAUTION - Again, the dimensions
are the MINIMUM length necessary to make the wire loops. I added an
additional 2" to each spreader. This makes the Reflector spreaders 32.7"
(30.7" + 2"), the Driven Element spreaders 31.2" (29.2" + 2") and the
Director spreaders 29.7" (27.7" + 2"). Using a drill press, drill a small
hole 1" from the end of each spreader. These holes will be used to run the
wire through, making the square loops. Take one of the 32.7" spreaders and
one of the 31.2" spreaders and using a saw, cut a slit on one end of each
spreader up to the hole you just drilled. Using care, make the slits wide
enough to slide the plexiglass into them. Drill an 1/8" hole near each end
of both pieces of plexiglass. Press the plexiglass into the slits, center
it and drill another 1/8" hole through the wood dowel and the plexiglass
1/2" from the end of the dowel. Refer to FIGURE 3. Attach the plexiglass
to the wood dowel with a small screw and some Elmers glue.
Now, using the drill press, drill a 1/2" hole 1" from the front end
of the boom. With the dimensions from the printout, drill a second hole
12.4" from the first hole, and so on, until all four holes are drilled.
These will be the holes for the horizontal spreaders. Rotate the boom 90
degrees on the drill press and measure 1/2" back from the middle of each
hole and mark it. Drill the other four holes for the vertical spreaders.
You'll also want to drill a couple of holes for mounting the antenna to
the mast. I used a muffler clamp and it seemed to work OK. You may have a
better way, especially if it's a horizontally polarized antenna. Drill the
two holes for the clamp about one foot from the rear end of the boom.
Remember, if the beam is vertically polarized then the holes for the clamp
must be drilled horizontally through the boom. You'll also need to drill a
small hole near the end of the boom to attach the support arm.
You can now insert the spreaders in the holes on the boom. I hung the
boom from the ceiling with some wire to keep it in the clear. Starting at
the rear of the boom, insert the long 32.7" spreader (with the plexiglass
insulator) into the hole. Moving toward the front of the boom, insert
the 31.2" spreader (with the plexiglass insulator) into the next hole.
Make sure the plexiglass insulators are both on the same side of the boom.
Continuing toward the front of the boom, insert two of the 29.7" spreaders
in the next two holes. You should now have 4 horizontal spreaders lined up
with the two shortest in the front of the boom and the longest at the
rear. Both plexiglass insulators should be on the same side. Using plenty
of Elmers glue, center each spreader and glue them in place. Be sure to
align the spreaders so that they are all parallel and make sure the holes
for the square wire loops are aligned properly. After the glue dries, do
the same for the vertical spreaders. Let the glue dry and put at least 2
coats of spar varnish on everything and let it dry over night.
You're now ready to string the wire loops through the cross-bars.
Using the dimensions from the printout, measure and cut the enameled wire
to length. CAUTION - Again the dimensions are for the exact length needed,
so you should add a little extra. I cut the directors one inch longer
(78.4" + 1") for a total of 79.4 inches. The Driven Element and the
Reflector need to be cut 4 inches longer. The extra length will be needed
for adjustment of the antenna. So, the Driven Element should be 86.5"
(82.5" + 4") and the Reflector should be 90.7" (86.7" + 4"). Now strip off
about 2 inches of enamel from each end of the Director wires and about 6"
of enamel from the Driven Element wire and Reflector wire. Feed one of the
Director wires through the holes on the end of each spreader at the front
Page 4
of the boom. Pull the wire tight making a square loop, overlap the two
ends by 1" and solder the connection. Do the same for the next Director.
Now take the Driven Element wire and feed it through each of the spreaders
with the ends of the wire terminating at the plexiglass insulator. Run
equal amounts of wire through the holes in the insulator, fold the wires
back and wrap each one around itself a couple of times. Point the ends of
the wires toward the front of the boom and solder the connection. Do the
same for the Reflector. You're going to need a shorting stub on the
Reflector to adjust the antenna. This can be made from a short piece of
copper wire. Cut a 2 1/2" piece of number 12 copper wire and bend the ends
over, making a small loop in each end. This will slide over the two ends
of the Reflector wires at the insulator. Push it all the way down to the
insulator for now, making the Reflector loop as short as possible. Refer
to FIGURE 4.
Antenna Adjustment
------------------
We're now ready to hook up the feedline, mount the antenna and make
some adjustments. The hard part is over. For VHF you should use low loss
cable like RG-213, for short runs you can get away with RG-8X. Separate
the center conductor from the shield for about 1 1/2". Twist the length
of exposed shield and tin the wire. Strip back 1/2" of insulation from the
center conductor and tin the wire. Bend a small loop in the end of both
the shield and center conductor. Connect the center conductor to one of
the ends of the Driven Element loop close to the insulator and the shield
to the other end of the loop the same distance from the insulator and
solder the connections. Using electrical tape, attach the coax to the
spreader and the boom, routing the coax down the boom through the
Reflector loop and out the rear of the antenna. You can now mount the
antenna to the mast but be careful, it's pretty bulky and fragile. This is
a good time to call on one of your Ham friends, they're always eager to
help with antennas. Refer to FIGURE 6 so you can understand the mounting
method using the Antenna Support Arm. With the antenna mounted in
position, hopefully well away from surrounding objects, you can hook up
the other end of the coax cable to your SWR meter and check the VSWR.
First take a reading at the Design Frequency and write it down. If the
VSWR is below 1.5 : 1 at the Design Frequency you might want to leave it
alone and get some signal reports from a few friends. Rotate the antenna
while listening to a weak station. You should see a big difference as you
point the beam in different directions. If the VSWR is too high, first
recheck all the dimensions, especially the Driven Element. The total
length of the Driven Element should be very close to the dimensions on the
printout. For our antenna, at 146 MHz., it should be about 82.5". That
includes the length of coax that was stripped back. Measure from where the
coax shield separates from the center conductor, all the way around the
spreaders and back to where the center conductor and shield separate. That
is the total length of the Driven Element. If that measures OK, then you
need to adjust the stub on the Reflector for the lowest VSWR. As a last
resort, you may need to move the coax connection at the feed point. If the
VSWR is Higher at a Lower frequency then you need to make the Driven
Element Longer. Keep the Feed Point the same distance from the insulator
for each connection to the coax. Remember, the antenna is influenced by
the Height above ground and Surrounding Objects, so keep it as high as
possible. Remember to solder the Reflector Shorting Stub when finished.
One final note - When building a Cubical Quad with only two elements,
Page 5
the characteristic impedance of the antenna will be well above 50 ohms.
Their are several ways to compensate for this. Two of the easiest ways are
to either decrease the spacing between the Driven Element and the
Reflector (about one half of what the printout recommends) or to use a 1/4
wavelength piece of 75 ohm coax as a linear transformer to feed the
antenna with. The rest of the feedline would still be 50 ohm coax.
Remember, we're talking about an electrical 1/4 wavelength (246 divided by
the Frequency times the Velocity Factor). For HF, the best way is to use a
Balun. In fact, you should always use a good Current Balun with any HF
antenna that uses coaxial cable as feedline.
Page 6
C O A X T R A P S
===================
By: John K. Agrelius, KM6HG
Coaxial Antenna Traps are antenna traps using coaxial cable. It's a
great way to make traps. They are inexpensive to make and work quite well.
With the inherent capacitance in coax all you have to do is wind it around
a form to create some inductance and Bingo.. you have a resonant circuit.
The trick is to make it resonant at the Design Frequency. That's what the
Coaxial Trap Design Program does.
Running the Program
-------------------
The program is quite simple to use. Just select your Coax Type and
enter the Form Diameter and the Design Frequency. When the calculations
are done and the dimensions are displayed you'll have 5 Choices:
#1 - This will Restart the Program.
#2 - This will Recalculate with a New Form Diameter & Frequency.
#3 - This will Recalculate with a New Frequency.
#4 - This will Print the Design Specifications of your Trap.
#5 - This will Quit the Program and Return to the Main Menu.
Building Your Traps
-------------------
The Form for your traps should be some type of round non-metallic
material. When I made my 40/75 meter Trap Dipole I used 3" ABS, which has
an outer diameter of 3.5". My Trap Design Frequency was 7.2 MHz. and my 75
meter frequency was 3.9 MHz. If you choose a Trap Design Frequency that's
a little on the low side, then the coax will be a little longer than you
actually need, so you'll have a safety margin. Let's go through it step by
step and build a 40/75 meter Trap Dipole like mine. You'll need to make
printouts for a 40 meter Dipole (Inverted Vee), a 75 meter Dipole and a
Trap for 40 meters.
The first thing you need to do is to build your antenna for the
Highest frequency (40 meters), let's say 7.2 MHz. Using the Inverted Vee
Program, the antenna would be 32.45 feet on each leg. Get your 40 meter
antenna adjusted for the lowest VSWR. Now you can build your traps. I used
RG-58C which was 5 Turns around my 3.5" Form and had to be 59.5" long (for
7.2 MHz). The width of the 5 Turns would be .97 inches, so I made my Form
4 inches long. That gave me an extra 1.5" on each end of the Form. I
drilled a 1/4" hole about 1/2" from each end of the two Forms. The holes
were used to connect the Form to the antenna. Remember, the 59.5 inches of
coax is the length of the shield. It's no longer coaxial cable where the
center conductor and shield are separated. I added 2 inches and cut the
coax to 61.5 inches. Separate the shield from the center conductor for 1
inch at each end of the 2 pieces of coax and tin the shield and the center
conductor. Wrap the coax around the Form (not too tight) and tape it off
neatly with electrical tape. You can run the tape in through the form and
Page 7
back over the coax. Don't cover up the ends of the coax. Now, take the
shield from one end and the center conductor from the other end and solder
them together. Refer to FIGURE 7. You may need some extra wire, I used
copper braid. Do the same with the other Trap.
You can now hook the Traps to the ends of the 40 meter antenna.
Replace the insulators at the end of each leg with the Traps. Any extra
wire, including the ends of the coax, that will be used to make the
connection, will become part of the antenna and must be subtracted from
the total length of the 40 meter antenna. I connected the center conductor
to the 40 meter side of the antenna and the shield to the 75 meter side.
Now you need to add the wire to the 75 meter side of the Trap to make your
75 meter antenna. This is the tricky part. There's no way to determine
precisely just how much wire you'll need. That's because the amount of
inductance in the Trap will be different at different frequencies, it will
change with the Form diameter, the type of coax used, etc. Besides, the
length of the ends of the antenna will also be affected by it's proximity
to ground. All we know for sure, is that the overall length of the antenna
will be shorter than a full length dipole for 75 meters. If you subtract
the length of the coax (59.5") from the length of one leg of the 75 meter
antenna (718.8"), this will give you 659.3". We also have to subtract the
length of the 40 meter leg to get our starting point. So, 659.3" - 389.4"
= 269.9" or about 22.5 feet. That's what we'll start with, and maybe a
little extra to be safe. Remember, it's easier to cut off extra antenna
wire than it is to stretch it, so always make it longer than you need.
Hook the 22.5 feet of wire to the 75 meter end of the Trap and solder the
connections on the Trap. Do the same for the other leg. Refer to FIGURE 8.
Antenna Trap Adjustment
-----------------------
With your SWR meter connected, check the VSWR at 7.2 MHz. The VSWR
should be very close to what it was as a 40 meter dipole (before the Traps
were added). Check the SWR Above and Below the Trap Design Frequency. If
the VSWR is better at a Lower frequency then you'll have to shorten the
coax on the Trap. It doesn't take much to make a difference. I only had to
take off 1/2" from each Trap. Just take a sharp knife and cut a slit down
through the shield and separate the center conductor from the shield a
little at a time and recheck the VSWR. If cutting the coax shorter makes
the VSWR worse, then there's a problem. Check all the dimensions, if
everything seems OK then you'll have to try again with a longer piece of
coax. This shouldn't happen but something could cause a problem, like the
Form material, weird coax or something else we're not aware of. Once
you've got a reasonable VSWR on 40 meters, you can check the antenna on 75
meters. You'll probably have to shorten the ends to get it resonant at 3.9
MHz. My antenna only needed a little less than 16 feet added to each Trap
to work on 75 meters but every installation is different. Don't forget to
seal the ends of the coax with some RTV. Have Fun and Good DX, John.
Page 8
Inverted Vee Diagrams
---------------------
_______________
| 1/4" v |
*|*O<- Holes ->O*|*
Wire Loop ------->* | * | * | *
* |* | *| *
* *| | |* *
Solder Joint ---->X | V | X
* s | O | c *
* s| |c *
Antenna Leg --->* |s c| *
* | s O c | *
* | s c | *
* Shield ------->s c<------- Center *
* | |X| | Conductor *
* Plexiglass ---->| |X| | *
* |______|X|______| *
|X|
50 Ohm Coax ---->|X|
|X|
|X|
|X|
FIGURE 1 - Inverted Vee Connections
_________________________________________________________________________
_
Plexiglass ---->|_|*
* | | *
* | | *
PVC Pipe ---------->| | *
* |-| *
* |X| *
Left Leg --->* |X| *<--- Right Leg
* |X| *
* |X| *
* Metal Mast --->|X| *
* |X| *
Insulator --->O |X| O
x |X| x
String -->x |X| x
+ |X| +
| |X| |
Pole -->| |X| |
| |X| |
------------------- Ground ----------------------- Ground ---------------
FIGURE 2 - Typical Inverted Vee Installation
Page 9
Cubical Quad Diagrams
---------------------
_______
| |
1/8" Hole ------>O |
| |
----------------------------------------
( O<--- 1/8" Hole Wood Dowel
----------------------------------------
| |
1/8" Hole ------>O |<---- Plexiglass
|_______|
FIGURE 3 - Insulators
_________________________________________________________________________
* *
* *
* *
*<------- Reflector Loop ------->*
* *
X<---------- Solder Joint ---------->X* * X * * * * *
* * * * *
____*__ * * _ * *
| * |* *| |* *
Hole ------>O* *| |*| *
| | | | *
---------------------- /| |\ * Reflector
( O <------ Wood Dowel ------->( | | ) *<-- Shorting
---------------------- \| |/ * Stub
| |<------------ Plexiglass ------------>| | *
Hole ------>O* *| |*| *
|___*___|* *|_|* *
* * * * *
* * * * *
X<--------- Solder Joint ----------->X* * X * * * * *
* *
*<------ Reflector Loop -------->*
* *
* *
Front View Side View
FIGURE 4 - Reflector Shorting Stub
Page 10
Cubical Quads (continued)
-------------------------
.\\ .
. \\ ' .
. \\ ' .
. \ __ ' .
_._______________________| |_______________________'_
- -----------------------|\\|-----------------------.-
' . | \\ . '
' . | \\ . '
' |. |\\ . '<---- 2nd Director
| | \\. ' Loop
.\\ .| |
. \\ | |' .
. \\| | ' .
. \| | ' .
_._______________________| |_______________________'_
- -----------------------|\\|-----------------------.-
' . | \\ . '
' . | \\ . '
' |. |\\ . '<---- 1st Director
| | \\. ' Loop
.\\ .| |
. \\ | |' .
Driven . \\| | ' .
Element | . \| | ' .
Feed ---> ||.________________________| |________________________'_
Point ---> |-------------------------|\\|------------------------.-
' . | \\ . '
' . | \\ . '
' . | |\\ . '<---- Driven Element
'| . \\. ' Loop
. \\. | |
. \\ | | ' .
. \\| | ' .
Reflector | . \| | ' .
Shorting ||._________________________| |_________________________'_
Stub ---> \|--------------------------|\\|-------------------------.-
' . | \\ . '
' . | \\ . '
' . | |\\ . '<---- Reflector
' | . \\. ' Loop
| |
| |
| |
*| || \ <------- Muffler Clamp
*| || /
| |
Muffler Clamp ------> *--| \ | |
*\\| / | |
\\ | |<------ Boom
\\ | |
\\ | |
Antenna Support Arm ------> \\| |
\|__|*
FIGURE 5 - Top View of 4 El. Quad
Page 11
Cubical Quads (continued)
-------------------------