Skip to content

Latest commit

 

History

History
118 lines (97 loc) · 7.74 KB

README.md

File metadata and controls

118 lines (97 loc) · 7.74 KB

RV-Link

Travis Build Status GitLab Build Status

A JTAG emulator/debugger for RISC-V micro-controllers that runs on a RISC-V development board (Sipeed Longan Nano for example).

JTAG emulators are the "umbilical cord" between PC software tools and MCU/DSP boards during development. Typically connecting to the host PC via parallel port or USB port, the JTAG emulator provides a standard, simple way to give the development tool software a direct connection to one or more MCU/DSP devices on the target board.

Like Blackmagic, but designed for RISC-V.

This project is based on the work of Zoomdy's RV-LINK project and is originally forked from the repository at https://gitee.com/zoomdy/RV-LINK.

Description

The goal of the RV-Link project is to provide the firmware needed to turn a RISC-V development board into a RISC-V emulator, but the RV-Link project does not include any hardware. Currently the RV-Link firmware runs on the boards listed below. The firmware can be loaded into the board using the dfu or serial uploading feature of its boot-loader, or if available, a JTAG emulator (which in turn could be a RV-Link ;-) ).

Different from other emulators: the RV-Link directly interacts with GDB through the USB serial port, and does not require an intermediary such as OpenOCD.

The development boards that can be used as emulators are:

  • Longan Nano, available on Taobao;
  • GD32VF103C-START, Taobao.

RISC-V MCU that RV-Link can debug:

  • GD32VF103 series.

Using RV-Link

The RV-Link firmware provides the following features when connected to a RISC-V target:

  • a JTAG interface with gbd-server as USB device e.g. on a Linux host connect to a target board with the following commands:

    $ riscv32-unknown-gdb <your-application-firmware.elf>
    (gdb) target remote /dev/ttyACM0
    (gbd) load
    (gdb) continue
    
  • a USB-to-serial adapter

    $ pio device monitor -p /dev/ttyACM1 -b 115200
    

    Before the USB-to-serial adapter feature can used, it must be activated with the GDB command mon rvl vcom on and subsequently the RV-Link must be power cycled to take effect. Note, this setting is persistent across power cycles, as it is stored in the build-in Flash memory of the RV-Link.

More resources

Building from source

This project currently only supports the PlatformIO build system, so you will need to install PlatformIO.

Run the following commands to build all firmware variants and upload the RV-Link firmware to e.g. the Sipeed Longan Nano RISC-V development board:

$ pio run
$ pio run -e sipeed-longan-nano -t upload

Wiring the RV-Link to a RISC-V target development board

The pins that are used for the JTAG/TAP hardware interface are configured during the build (determined by platformio.ini and link-config.h) and are as following:

  • gd32vf103c-start
    • TMS = PB12/NSS1, TCK = PB13/SCK1, TDO = PB14/MISO1, TDI = PB15/MOSI1, SRST = PB0/GPIO
    • VCOM = PA9/UART0_TX, PA10/UART0_RX
  • sipeed-longan-nano
    • TMS = PA13/GPIO, TCK = PA14/GPIO, TDO = PB3/GPIO, TDI = PB15/GPIO, SRST = N/A
    • VCOM = PA9/UART0_TX, PA10/UART0_RX
  • sipeed-longan-nano-alt
    • TMS = PB12/NSS1, TCK = PB13/SCK1, TDO = PB14/MISO1, TDI=PB15/MOSI1, SRST = PA8/GPIO
    • VCOM = PA9/UART0_TX, PA10/UART0_RX
  • rvl-probe
    • TMS = PA4/NSS0, TCK = PA5/SCK0, TDO = PA6/MISO0, TDI = PA7MOSI0, SRST = N/A
    • VCOM = PB10/UART2_TX, PB11/UART2_RX
    • CAN = B12/CAN1_RX, PB13/CAN1_TX

Optionally, the serial interface of the RV-Link can be cross-connected to an UART of the target board.

Note

When the JTAG pins are not properly connected, it is very likely that you will see the following output:

(gdb) target remote /dev/ttyACM0
Remote debugging using /dev/ttyACM0
Remote replied unexpectedly to 'vMustReplyEmpty': 
RV-LINK ERROR: the target is not connected!
RV-LINK v0.2: Longan Nano, configed for GD32VF103 family.

If so, check your wiring, optionally add series resistors (of e.g. 100Ohm) in each JTAG signal wire at the RV-Link.

A wiring example

Here is an example of a Sipeed Longan Nano running the RV-Link firmware (env:sipeed-longan-nano) that is debugging a Sipeed Longan Nano running the RV-Link firmware (env:rvl-probe) that is debugging a third Sipeed Longan Nano running a blink application...

Suggested improvements

This project aims to improve the original RV-LINK firmware with the following features:

  • Support for a newly designed hardware board with specific features, called RVL-Probe
  • Support for JTAG over SPI + DMA;
  • Additional diagnostics of the JTAG interface;
  • Support for a second USB to serial adapter;
  • A CAN bus logger;
  • Easy updating of the RV-Link firmware;
  • Support of running RV-Link on other host platforms (e.g. Linux PC+FT323 / Raspberry Pi);
  • Additional mon commands;
  • Additional NVM configurable items.

Download firmware files

Notes

This repository originally based on the RV-LINK project of Zoomdy and was forked from the repository at https://gitee.com/zoomdy/RV-LINK at the v0.2.1 tag. It is mirrored to GitHub and Gitee.