Replies: 7 comments 19 replies
-
|
I have updated to MissionControl 0.6.0 and 13.0.0 firmware ,but here comes a new problem to me.While pairing my controller lanShen X1Pro requested @#213,the screen shows connetting success,but the led just flash 1s and disconnected.If there is a bug or not,hope can |
Beta Was this translation helpful? Give feedback.
-
|
Which version are you updating from? In 0.5.0 I changed the default behaviour of blocking the SetTsi command to all controllers as it was responsible for some latency and network bandwidth issues. It's likely this is another controller that doesn't like receiving this command and will need to have it blocked again. If you have been previously using the controller with 0.5.x successfully then it might be some new 13.0.0 behaviour that the controller doesn't like and will require some investigation. |
Beta Was this translation helpful? Give feedback.
-
|
With this release (based on the changelog), it means that Wii U Pro Con will have a correct battery level report? |
Beta Was this translation helpful? Give feedback.
-
|
I was under the impression it was already correct, but @GaryOderNichts was not so sure. What this does is reads the battery level (along with charging status) from the button input reports instead of the periodic status reports used by other Wii controllers. This isn't well documented and I wasn't aware that the Wii U Pro controller sent this info previously. |
Beta Was this translation helpful? Give feedback.
-
|
Update from 0.4.1.Maybe it can't work in 0.5.0,so sad |
Beta Was this translation helpful? Give feedback.
-
|
Thanks for the answer. |
Beta Was this translation helpful? Give feedback.
-
|
Bravo!It works. |
Beta Was this translation helpful? Give feedback.
-
|
@ndeadly I tried also with the Xbox controller, same problem. I've done exactly what explained in the guide. Can you verify if the are some compatibility issues with Atmosphere v1.1.1? |
Beta Was this translation helpful? Give feedback.
-
|
boa noite amigo so uma pergunta ele nao apareci mais o iconi mais nao pq antas tinha mais agora nao to vendo ele nao aparece na homer bril ?????????? |
Beta Was this translation helpful? Give feedback.
-
@ndeadly I skipped that part... |
Beta Was this translation helpful? Give feedback.
-
|
English please |
Beta Was this translation helpful? Give feedback.
-
|
Pls! Help me! I cant install mission control, i will copy all file and paste in my SD card but not work. My atmosphere is Kefir 621 |
Beta Was this translation helpful? Give feedback.
-
|
Did you follow the installation and pairing instructions? Not working can mean many things. You're going to have to be more specific if you want help. |
Beta Was this translation helpful? Give feedback.
-
|
i will paste all file in my SD card but in my Hbmenu dont have mission cotrol, i can install with HB app store but in HB app store have 0.5.0. (sorry my english very bad) |
Beta Was this translation helpful? Give feedback.
-
|
Have you read the readme and instructions? MissionControl by now hasn't an interface, mission control intercept the Bluetooth communication, the user interface is the same of the system. There is an application but is only intented for diagnostics and isn't part of the official release |
Beta Was this translation helpful? Give feedback.
-
|
Is supposed what Kefir 621 is a pre-cooked package with MissionControl 0.6.0 preinstalled, so is supposed mission controll should work fine on your environment IF YOU follor all the instructions, the Kefir and MissionControl ones, please repeat the installation and read the use instructions stated on main page of MissionControll. |
Beta Was this translation helpful? Give feedback.
-
|
I’ve just updated to 13.0.0 and atm 1.1.1|S and Mission Contoller 0.6.0. I’ve done it in other versions, it always works, but in this version no. “Panic occurred while runing atmosphere” when conect PS4 controller |
Beta Was this translation helpful? Give feedback.
-
|
I'm going to guess there's some kind of version mismatch going on here. Why not use the latest versions of both Atmosphere (1.2.2) and Mission Control (0.6.1)? |
Beta Was this translation helpful? Give feedback.
-
|
Atmosphere 1.2.2 works with 13.0.0, no? I change the sigpages and the folder atmosphere, no? |
Beta Was this translation helpful? Give feedback.
-
|
13.1.0 and Atmosphere 1.2.1, it using Mission Control 0.6.1, it doesn’t work… same error, any ideas. |
Beta Was this translation helpful? Give feedback.
-
|
It works in atm 1.2.2 |
Beta Was this translation helpful? Give feedback.
-
This is the ninth official release of Mission Control
This release brings full support for firmware 13.0.0, along with a few minor additions and bugfixes. See the changelog below for details.
New users landing on this release page should first check out the readme on the main project page for the official project documentation. There you can find installation and usage instructions along with an FAQ section that will answer most of your questions.
Note: 13.0.0 firmware made changes to the system to facilitate bluetooth audio support. While I have updated Mission Control to support the changes that concern hid devices, it's possible that there are issues that could arise from untested scenarios involving audio devices. If you notice any strange behaviour with audio devices that only occurs with mission control installed, please open an issue on the issue tracker.
Atmosphère >= 1.1.0 is required to run this release.
Important notice for users of Xbox One controllers
With news of a new insiders firmware update to bring next-gen features to existing Xbox One controllers, it may be tempting to download and install the firmware when it becomes available to you. From what I can tell from the linked news article and some intial reports, this update may configure your controller to use Bluetooth LE for connections instead of the current classic Bluetooth, effectively converting it into a Series S/X controller. This means your controller will likely be rendered incompatible with Mission Control until I am able to add Bluetooth LE support. You have been warned.
Changelog:
/config/MissionControl/controllersdirectory is now created as required if not present. This avoids potential crashes eg. if the user has deleted this directory, or has failed to install the module correctly.This discussion was created from the release MissionControl 0.6.0.
Beta Was this translation helpful? Give feedback.
All reactions