Update to release v2.2

Tuned 0.4n profiles
increased speed
added better support break-away
finetuned retraction

Config files/filament/PLA @E2.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.3.0-rc2+win64 on 2021-01-08 at 08:52:29 UTC
+# generated by PrusaSlicer 2.3.0+win64 on 2021-02-11 at 13:58:34 UTC
 bed_temperature = 60
 bridge_fan_speed = 100
 compatible_printers = 
@@ -8,9 +8,9 @@ compatible_prints_condition =
 cooling = 1
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
-extrusion_multiplier = 1
+extrusion_multiplier = 1.1
 fan_always_on = 1
-fan_below_layer_time = 100
+fan_below_layer_time = 60
 filament_colour = #FF8000
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
@@ -30,7 +30,7 @@ filament_retract_before_travel = nil
 filament_retract_before_wipe = nil
 filament_retract_layer_change = nil
 filament_retract_length = nil
-filament_retract_lift = 0.2
+filament_retract_lift = nil
 filament_retract_lift_above = nil
 filament_retract_lift_below = nil
 filament_retract_restart_extra = nil
@@ -46,12 +46,12 @@ filament_unloading_speed_start = 100
 filament_vendor = (Unknown)
 filament_wipe = nil
 first_layer_bed_temperature = 60
-first_layer_temperature = 215
-full_fan_speed_layer = 4
+first_layer_temperature = 220
+full_fan_speed_layer = 0
 inherits = 
 max_fan_speed = 100
 min_fan_speed = 100
-min_print_speed = 15
-slowdown_below_layer_time = 15
+min_print_speed = 25
+slowdown_below_layer_time = 8
 start_filament_gcode = "; Filament gcode\nM572 D0 S0.07\nM572 D1 S0.07"
 temperature = 215

Config files/print/0.10mm @E2 0.4.ini

@@ -1,13 +1,13 @@
-# generated by PrusaSlicer 2.3.0-rc2+win64 on 2021-01-08 at 09:07:22 UTC
+# generated by PrusaSlicer 2.3.0+win64 on 2021-02-16 at 10:34:18 UTC
 avoid_crossing_perimeters = 0
 avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonic
 bottom_solid_layers = 7
 bottom_solid_min_thickness = 0.5
 bridge_acceleration = 0
 bridge_angle = 0
-bridge_flow_ratio = 0.8
-bridge_speed = 25
+bridge_flow_ratio = 1.4
+bridge_speed = 15
 brim_width = 0
 clip_multipart_objects = 1
 compatible_printers = 
@@ -19,7 +19,7 @@ draft_shield = 0
 elefant_foot_compensation = 0.2
 ensure_vertical_shell_thickness = 1
 external_perimeter_extrusion_width = 0.45
-external_perimeter_speed = 35
+external_perimeter_speed = 72
 external_perimeters_first = 0
 extra_perimeters = 0
 extruder_clearance_height = 27
@@ -32,7 +32,7 @@ first_layer_acceleration = 0
 first_layer_extrusion_width = 0.42
 first_layer_height = 0.2
 first_layer_speed = 15
-gap_fill_speed = 50
+gap_fill_speed = 25
 gcode_comments = 0
 gcode_label_objects = 0
 infill_acceleration = 0
@@ -43,8 +43,8 @@ infill_extruder = 1
 infill_extrusion_width = 0.45
 infill_first = 0
 infill_only_where_needed = 0
-infill_overlap = 30%
-infill_speed = 70
+infill_overlap = 0
+infill_speed = 72
 inherits = 
 interface_shells = 0
 ironing = 0
@@ -53,18 +53,18 @@ ironing_spacing = 0.1
 ironing_speed = 15
 ironing_type = top
 layer_height = 0.1
-max_print_speed = 90
+max_print_speed = 130
 max_volumetric_speed = 0
 min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45
-perimeter_speed = 45
+perimeter_speed = 80
 perimeters = 2
 post_process = 
 print_settings_id = 
@@ -76,12 +76,12 @@ skirt_distance = 2
 skirt_height = 3
 skirts = 1
 slice_closing_radius = 0.049
-small_perimeter_speed = 25
+small_perimeter_speed = 27
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0.45
-solid_infill_speed = 60
+solid_infill_speed = 72
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 0
@@ -94,11 +94,11 @@ support_material_extruder = 1
 support_material_extrusion_width = 0.55
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
-support_material_interface_layers = 2
-support_material_interface_spacing = 0.2
+support_material_interface_layers = 3
+support_material_interface_spacing = 2.5
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
-support_material_spacing = 2
+support_material_spacing = 2.5
 support_material_speed = 45
 support_material_synchronize_layers = 0
 support_material_threshold = 55
@@ -108,7 +108,7 @@ thin_walls = 0
 threads = 16
 top_fill_pattern = monotonic
 top_infill_extrusion_width = 0.4
-top_solid_infill_speed = 60
+top_solid_infill_speed = 72
 top_solid_layers = 9
 top_solid_min_thickness = 0.6
 travel_speed = 150

Config files/print/0.15mm @E2 0.4.ini

@@ -1,13 +1,13 @@
-# generated by PrusaSlicer 2.3.0-rc2+win64 on 2021-01-08 at 09:06:52 UTC
+# generated by PrusaSlicer 2.3.0+win64 on 2021-02-16 at 10:35:09 UTC
 avoid_crossing_perimeters = 0
 avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonic
 bottom_solid_layers = 5
 bottom_solid_min_thickness = 0.5
 bridge_acceleration = 0
 bridge_angle = 0
-bridge_flow_ratio = 0.9
-bridge_speed = 25
+bridge_flow_ratio = 1.4
+bridge_speed = 15
 brim_width = 0
 clip_multipart_objects = 1
 compatible_printers = 
@@ -19,7 +19,7 @@ draft_shield = 0
 elefant_foot_compensation = 0.2
 ensure_vertical_shell_thickness = 1
 external_perimeter_extrusion_width = 0.45
-external_perimeter_speed = 35
+external_perimeter_speed = 72
 external_perimeters_first = 0
 extra_perimeters = 0
 extruder_clearance_height = 27
@@ -32,7 +32,7 @@ first_layer_acceleration = 0
 first_layer_extrusion_width = 0.42
 first_layer_height = 0.2
 first_layer_speed = 15
-gap_fill_speed = 50
+gap_fill_speed = 25
 gcode_comments = 0
 gcode_label_objects = 0
 infill_acceleration = 0
@@ -43,8 +43,8 @@ infill_extruder = 1
 infill_extrusion_width = 0.45
 infill_first = 0
 infill_only_where_needed = 0
-infill_overlap = 30%
-infill_speed = 70
+infill_overlap = 0
+infill_speed = 72
 inherits = 
 interface_shells = 0
 ironing = 0
@@ -53,18 +53,18 @@ ironing_spacing = 0.1
 ironing_speed = 15
 ironing_type = top
 layer_height = 0.15
-max_print_speed = 90
+max_print_speed = 130
 max_volumetric_speed = 0
 min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45
-perimeter_speed = 45
+perimeter_speed = 80
 perimeters = 2
 post_process = 
 print_settings_id = 
@@ -76,12 +76,12 @@ skirt_distance = 2
 skirt_height = 3
 skirts = 1
 slice_closing_radius = 0.049
-small_perimeter_speed = 25
+small_perimeter_speed = 27
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0.45
-solid_infill_speed = 60
+solid_infill_speed = 72
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 0
@@ -94,11 +94,11 @@ support_material_extruder = 1
 support_material_extrusion_width = 0.55
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
-support_material_interface_layers = 2
-support_material_interface_spacing = 0.2
+support_material_interface_layers = 3
+support_material_interface_spacing = 2.5
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
-support_material_spacing = 2
+support_material_spacing = 2.5
 support_material_speed = 45
 support_material_synchronize_layers = 0
 support_material_threshold = 55
@@ -108,7 +108,7 @@ thin_walls = 0
 threads = 16
 top_fill_pattern = monotonic
 top_infill_extrusion_width = 0.4
-top_solid_infill_speed = 60
+top_solid_infill_speed = 72
 top_solid_layers = 7
 top_solid_min_thickness = 0.6
 travel_speed = 150

Config files/print/0.20mm @E2 0.4.ini

@@ -1,13 +1,13 @@
-# generated by PrusaSlicer 2.3.0-rc2+win64 on 2021-01-05 at 18:08:23 UTC
+# generated by PrusaSlicer 2.3.0+win64 on 2021-02-15 at 14:10:35 UTC
 avoid_crossing_perimeters = 0
 avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonic
 bottom_solid_layers = 4
 bottom_solid_min_thickness = 0.5
 bridge_acceleration = 0
 bridge_angle = 0
-bridge_flow_ratio = 0.95
-bridge_speed = 25
+bridge_flow_ratio = 1.4
+bridge_speed = 15
 brim_width = 0
 clip_multipart_objects = 1
 compatible_printers = 
@@ -19,8 +19,8 @@ draft_shield = 0
 elefant_foot_compensation = 0.2
 ensure_vertical_shell_thickness = 1
 external_perimeter_extrusion_width = 0.45
-external_perimeter_speed = 35
-external_perimeters_first = 0
+external_perimeter_speed = 72
+external_perimeters_first = 1
 extra_perimeters = 0
 extruder_clearance_height = 27
 extruder_clearance_radius = 52
@@ -32,7 +32,7 @@ first_layer_acceleration = 0
 first_layer_extrusion_width = 0.42
 first_layer_height = 0.2
 first_layer_speed = 15
-gap_fill_speed = 50
+gap_fill_speed = 25
 gcode_comments = 0
 gcode_label_objects = 0
 infill_acceleration = 0
@@ -43,8 +43,8 @@ infill_extruder = 1
 infill_extrusion_width = 0.45
 infill_first = 0
 infill_only_where_needed = 0
-infill_overlap = 30%
-infill_speed = 70
+infill_overlap = 0
+infill_speed = 72
 inherits = 
 interface_shells = 0
 ironing = 0
@@ -53,35 +53,35 @@ ironing_spacing = 0.1
 ironing_speed = 15
 ironing_type = top
 layer_height = 0.2
-max_print_speed = 90
+max_print_speed = 130
 max_volumetric_speed = 0
 min_skirt_length = 4
 notes = 
-only_retract_when_crossing_perimeters = 0
+only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}_{total_weight}g.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45
-perimeter_speed = 45
+perimeter_speed = 80
 perimeters = 2
 post_process = 
 print_settings_id = 
 raft_layers = 0
 resolution = 0
-seam_position = nearest
+seam_position = aligned
 single_extruder_multi_material_priming = 0
 skirt_distance = 2
 skirt_height = 3
 skirts = 1
 slice_closing_radius = 0.049
-small_perimeter_speed = 25
+small_perimeter_speed = 27
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0.45
-solid_infill_speed = 60
+solid_infill_speed = 72
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 0
@@ -94,11 +94,11 @@ support_material_extruder = 1
 support_material_extrusion_width = 0.55
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
-support_material_interface_layers = 2
-support_material_interface_spacing = 0.2
+support_material_interface_layers = 3
+support_material_interface_spacing = 2.5
 support_material_interface_speed = 100%
 support_material_pattern = rectilinear
-support_material_spacing = 2
+support_material_spacing = 2.5
 support_material_speed = 45
 support_material_synchronize_layers = 0
 support_material_threshold = 55
@@ -108,7 +108,7 @@ thin_walls = 0
 threads = 16
 top_fill_pattern = monotonic
 top_infill_extrusion_width = 0.4
-top_solid_infill_speed = 60
+top_solid_infill_speed = 72
 top_solid_layers = 5
 top_solid_min_thickness = 0.6
 travel_speed = 150