BMP388 Library for Arduino/ESP32/RaspberrayPi

This is a Library for BMP388, the function is to read temperature and pressure.

Table of Contents

• Summary
• Methods
• Compatibility
• History
• Credits

Summary

• BMP388 can read temperature and pressure.
• The library supports the SPI/I2C communication.
• This library provides examples of calculating and calibrating altitude.
• The sensor is more accurate than its predecessors, covering a wide measurement range from 300 hPa to 1250 hPa.
• This new barometric pressure sensor exhibits an attractive price-performance ratio coupled with low power consumption.

Methods

Arduino

#include <DFRobot_BMP388.h>
/*
 * @brief bmp388 I2C constructor
 */
DFRobot_BMP388_I2C();

/*
 * @brief bmp388 SPI constructor
 *
 * @param cs Chip selection pin of SPI
 */
DFRobot_BMP388_SPI(int cs);

/* 
 * @brief Set bmp388 IIC address
 * @param addr BMP3_I2C_ADDR_PRIM: pin SDO is low
 *             BMP3_I2C_ADDR_SEC: pin SDO is high
 */
void set_iic_addr(uint8_t addr);

/*
 * @brief Initialize bmp388, check for chip id, reset the sensor, read the calibration data and config sensor
 *
 * @return 0 if success
 */
int8_t begin();

/*
 * @brief Read temperature
 *
 * @return temperature
 */
float readTemperature();

/*
 * @brief Read pressure.
 *
 * @return Pressure
 */
float readPressure();

/*
 * @brief Read normalised atmospheric pressure of sea level
 *
 * @param altitude The local elevation
 *
 * @return Pressure of sea level
 */
float readSeaLevel(float altitude);

/*
 * @brief Read calibrated elevation.
 *
 * @param seaLevel Pressure of sea level
 *
 * @return Calibrated elevation
 */
float readCalibratedElevation(float seaLevel);

/*
 * @brief Read elevation.
 *
 * @return elevation
 */
float readElevation(void);

/*
 * @brief Enable INT.
 */
void INTEnable();

/*
 * @brief Disable INT.
 */
void INTDisable();

micropython

import bmp388

/*
 * @brief bmp388 I2C constructor
 *
 * @param i2c I2C object.
 */
DFRobot_BMP388_I2C(i2c)

/*
 * @brief bmp388 SPI constructor
 *
 * @param spi SPI object.
 *        cs  Chip selection pin of SPI
 */
DFRobot_BMP388_SPI(spi,cs)

/*
 * @brief Read temperature
 *
 * @return Temperature
 */
readTemperature()

/*
 * @brief Read pressure.
 *
 * @return pressure
 */
readPressure()

/*
 * @brief Read normalised atmospheric pressure of sea level
 *
 * @param altitude The local elevation
 *
 * @return Pressure of sea level
 */
readSeaLevel(altitude)

/*
 * @brief Read calibrated elevation.
 *
 * @param seaLevel Pressure of sea level
 *
 * @return Calibrated elevation
 */
readCalibratedElevation(seaLevel)

/*
 * @brief Read elevation.
 *
 * @return elevation
 */
readElevation()

/*
 * @brief Enable INT.
 */
INTEnable()

/*
 * @brief Disable INT.
 */
INTDisable()

Raspberry Pi

import bmp388

/*
 * @brief bmp388 I2C constructor
 */
DFRobot_BMP388_I2C()

/*
 * @brief bmp388 SPI constructor
 *
 * @param cs Chip selection pin of SPI
 */
DFRobot_BMP388_SPI(cs)

/*
 * @brief Read temperature
 *
 * @return temperature
 */
readTemperature()

/*
 * @brief Read pressure.
 *
 * @return pressure
 */
readPressure()

/*
 * @brief Read normalised atmospheric pressure of sea level
 *
 * @param altitude The local elevation
 *
 * @return Pressure of sea level
 */
readSeaLevel(altitude)

/*
 * @brief Read calibrated elevation.
 *
 * @param seaLevel Pressure of sea level
 *
 * @return Calibrated elevation
 */
readCalibratedElevation(seaLevel)

/*
 * @brief Read elevation.
 *
 * @return elevation
 */
readElevation()

/*
 * @brief Enable INT.
 */
INTEnable()

/*
 * @brief Disable INT.
 */
INTDisable()

Compatibility

MCU	Work Well	Work Wrong	Untested	Remarks
FireBeetle-ESP32	√
RaspberrayPi	√			Only support python3
Arduino	√

History

• data 2018-6-2
• version V0.1

Credits

• author [Luyuhao yuhao.lu@dfrobot.com]