feat(Examples,MiscDrivers): Add OV5640 DVP camera driver (analogdevic…

…esinc#644)

Examples/MAX78000/CameraIF/README.md

@@ -5,6 +5,7 @@ This example demonstrates the Parallel Camera Interface (PCIF) drivers and camer
 * OV7962 (Default)
 * HM0360 (MONO), for color use the CameraIF_Debayer example
 * OV5642
+* OV5640
 * HM01B0
 
 ## Software

Examples/MAX78000/CameraIF/main.c

@@ -33,7 +33,7 @@
 
 /**
  * @file    main.c
- * @brief   Parallel camera example with the OV7692/OV5642/HM01B0/HM0360/PAG7920 camera sensors as defined in the makefile.
+ * @brief   Parallel camera example with the OV7692/OV5642/OV5640/HM01B0/HM0360/PAG7920 camera sensors as defined in the makefile.
  *
  * @details This example uses the UART to stream out the image captured from the camera.
  *          Alternatively, it can display the captured image on TFT is it is enabled in the make file.
@@ -56,8 +56,10 @@
 #include "uart.h"
 #include "led.h"
 #include "board.h"
-
 #include "camera.h"
+#if defined(OV5640_DVP)
+#include "mipi_camera.h"
+#endif
 #include "utils.h"
 #include "dma.h"
 
@@ -68,8 +70,8 @@
 /* If enabled, camera is setup in streaming mode to send the image
 line by line to TFT, or serial port as they are captured. Otherwise, it buffers the entire
 image first and then sends to TFT or serial port.
-With serial port set at 900kbps, it can stream for up to 80x80 with OV5642 camera in 
-stream mode, or 176x144 when stream mode is disabled.  It can display on TFT up to 176x144 
+With serial port set at 900kbps, it can stream for up to 80x80 with OV5642 camera in
+stream mode, or 176x144 when stream mode is disabled.  It can display on TFT up to 176x144
 if stream mode is disabled, or 320x240 if enabled
 */
 // #define BUTTON
@@ -134,8 +136,7 @@ Compiler definitions...  These configure TFT and camera settings based on the op
 
 #endif
 
-#if defined(CAMERA_OV7692) || defined(CAMERA_OV5642)
-
+#if defined(CAMERA_OV7692) || defined(CAMERA_OV5642) || defined(CAMERA_OV5640)
 #ifdef ENABLE_TFT
 #ifdef STREAM_ENABLE
 #define IMAGE_XRES 320
@@ -281,13 +282,13 @@ int main(void)
 
     // Initialize the camera driver.
     camera_init(CAMERA_FREQ);
-    printf("\n\nCamera Example\n");
+    printf("\n\nCameraIF Example\n");
 
     slaveAddress = camera_get_slave_address();
     printf("Camera I2C slave address: %02x\n", slaveAddress);
 
-    // Obtain the manufacturer ID of the camera.
-    ret = camera_get_manufacture_id(&id);
+    // Obtain product ID of the camera.
+    ret = camera_get_product_id(&id);
 
     if (ret != STATUS_OK) {
         printf("Error returned from reading camera id. Error %d\n", ret);
@@ -334,8 +335,13 @@ int main(void)
     // Setup the camera image dimensions, pixel format and data acquiring details.
 #ifndef STREAM_ENABLE
 #ifndef CAMERA_MONO
+#if defined(OV5640_DVP)
+    ret = camera_setup(IMAGE_XRES, IMAGE_YRES, PIXEL_FORMAT_RGB565, FIFO_FOUR_BYTE, USE_DMA,
+                       dma_channel); // RGB565
+#else
     ret = camera_setup(IMAGE_XRES, IMAGE_YRES, PIXFORMAT_RGB565, FIFO_FOUR_BYTE, USE_DMA,
                        dma_channel); // RGB565
+#endif
 #else
     ret = camera_setup(IMAGE_XRES, IMAGE_YRES, PIXFORMAT_BAYER, FIFO_FOUR_BYTE, USE_DMA,
                        dma_channel); // Mono
@@ -352,8 +358,13 @@ int main(void)
 #else //STREAM_ENABLE
 #ifndef CAMERA_MONO
 #ifndef FEATHER_FAST_STREAM
+#if defined(OV5640_DVP)
+    ret = camera_setup(IMAGE_XRES, IMAGE_YRES, PIXEL_FORMAT_RGB565, FIFO_FOUR_BYTE, STREAMING_DMA,
+                       dma_channel); // RGB565
+#else
     ret = camera_setup(IMAGE_XRES, IMAGE_YRES, PIXFORMAT_RGB565, FIFO_FOUR_BYTE, STREAMING_DMA,
-                       dma_channel); // RGB565 stream
+                       dma_channel); // RGB565
+#endif
 #else
     MXC_TFT_Stream(0, 0, IMAGE_XRES, IMAGE_YRES);
     ret = camera_setup_tft(IMAGE_XRES, IMAGE_YRES, PIXFORMAT_RGB565, FIFO_FOUR_BYTE, STREAMING_DMA,
@@ -379,6 +390,9 @@ int main(void)
         return -1;
     }
 
+#if defined(OV5640_DVP)
+    camera_write_reg(0x503d, 0x0); // workaround: disable test pattern: color bar
+#endif
     MXC_Delay(SEC(1));
 
     // Start capturing a first camera image frame.

Examples/MAX78000/CameraIF/project.mk

@@ -14,6 +14,7 @@
 # For a full list of options for the 'CAMERA' variable, 
 # see the documentation.
 CAMERA=OV7692
+#CAMERA=OV5640
 #CAMERA=OV5642
 #CAMERA=HM0360_MONO
 #CAMERA=HM01B0

Examples/MAX78002/CameraIF/README.md

@@ -34,6 +34,7 @@ To change the camera drivers set the `CAMERA` build configuration variable in [p
 
 Additionally, ensure JP38 (DVP CAM PWR) is connected properly.
 -   OV7692:  Connect JP38 to "ON"
+-   OV5640:  Connect JP38 to "ON"
 -   HM0360:  Connect JP38 to "OFF"
 
 Consult your camera module's power-down logic and the MAX78002EVKIT schematic for other camera modules.  

Examples/MAX78002/CameraIF/main.c

@@ -33,7 +33,7 @@
 
 /**
  * @file    main.c
- * @brief   Parallel camera example with the OV7692/OV5642/HM01B0/HM0360 camera sensors as defined in the makefile.
+ * @brief   Parallel camera example with the OV7692/OV5642/OV5640/HM01B0/HM0360/PAG7920 camera sensors as defined in the makefile.
  *
  * @details This example uses the UART to stream out the image captured from the camera.
  *          Alternatively, it can display the captured image on TFT is it is enabled in the make file.
@@ -58,6 +58,7 @@
 #include "led.h"
 #include "board.h"
 #include "camera.h"
+#include "mipi_camera.h"
 #include "utils.h"
 #include "dma.h"
 #ifdef TFT_ADAFRUIT
@@ -75,17 +76,18 @@
 #if defined(CAMERA_HM01B0)
 #define IMAGE_XRES 324 / 2
 #define IMAGE_YRES 244 / 2
+#define CAMERA_MONO
 #endif
 
-#if defined(CAMERA_HM0360_MONO)
+#if defined(CAMERA_HM0360_MONO) || defined(CAMERA_PAG7920)
 #define IMAGE_XRES 320
 #define IMAGE_YRES 240
+#define CAMERA_MONO
 #endif
 
-#if defined(CAMERA_OV7692) || defined(CAMERA_OV5642)
+#if defined(CAMERA_OV7692) || defined(CAMERA_OV5642) || defined(CAMERA_OV5640)
 #define IMAGE_XRES 320
 #define IMAGE_YRES 240
-
 #endif
 
 #define CON_BAUD \
@@ -160,7 +162,8 @@ int main(void)
 
     printf("Camera ID detected: %04x\n", id);
 
-#if defined(CAMERA_HM01B0) || defined(CAMERA_HM0360_MONO) || defined(CAMERA_OV5642)
+#if defined(CAMERA_HM01B0) || defined(CAMERA_HM0360_MONO) || defined(CAMERA_OV5642) || \
+    defined(CAMERA_OV5640)
     camera_set_vflip(0);
 #ifdef TFT_NEWHAVEN
     // Newhaven display needs a horizontal flip to match orientation
@@ -192,14 +195,19 @@ int main(void)
     }
     // Set 0 rotation to match camera orientation
     MXC_TFT_SetRotation(ROTATE_0);
-#endif
 #endif
     MXC_TFT_SetBackGroundColor(0);
+#endif
 
     // Setup the camera image dimensions, pixel format and data acquiring details.
 #ifndef CAMERA_MONO
+#if defined(OV5640_DVP)
+    ret = camera_setup(IMAGE_XRES, IMAGE_YRES, PIXEL_FORMAT_RGB565, FIFO_FOUR_BYTE, USE_DMA,
+                       dma_channel); // RGB565
+#else
     ret = camera_setup(IMAGE_XRES, IMAGE_YRES, PIXFORMAT_RGB565, FIFO_FOUR_BYTE, USE_DMA,
                        dma_channel); // RGB565
+#endif
 #else
     ret = camera_setup(IMAGE_XRES, IMAGE_YRES, PIXFORMAT_BAYER, FIFO_FOUR_BYTE, USE_DMA,
                        dma_channel); // Mono
@@ -210,9 +218,13 @@ int main(void)
         return -1;
     }
 
-    // Start capturing a first camera image frame.
-    printf("Capture image\n");
+#if defined(OV5640_DVP)
+    camera_write_reg(0x503d, 0x0); // workaround: disable test pattern: color bar
+#endif
+
+    // Start capturing a first  camera image frame.
     camera_start_capture_image();
+    printf("Capture image\n");
 
     while (1) {
         // Check if image is acquired.
@@ -226,6 +238,7 @@ int main(void)
             // Prepare for another frame capture.
             LED_Toggle(LED1);
             camera_start_capture_image();
+            printf(".\n");
         }
     }
 

Examples/MAX78002/CameraIF/project.mk

@@ -15,16 +15,21 @@
 # connected camera.  These are some common values.  
 # For a full list of options for the 'CAMERA' variable, 
 # see the documentation.
-CAMERA=OV7692
-#CAMERA=OV5640
-# CAMERA=HM0360_MONO
+#CAMERA=OV7692
+CAMERA=OV5640
+#CAMERA=OV5642
+#CAMERA=HM0360_MONO
 #CAMERA=HM01B0
 
+ifeq "$(CAMERA)" "OV5640"
+PROJ_CFLAGS+=-DOV5640_DVP
+endif
+
 # Uncomment to use legacy Adafruit 3315 TFT drivers (TFT = ADAFRUIT)
 # Otherwise, default drivers (TFT = NEWHAVEN) will be used for NewHaven NHD-2.4
 # TFT = ADAFRUIT
 
 # Set a higher optimization level.  The increased performance
 # is required for the CameraIF DMA code to work within the
 # timing requirements of the Parallel Camera Interface.
-MXC_OPTIMIZE_CFLAGS = -O2
+MXC_OPTIMIZE_CFLAGS = -O2

Libraries/Boards/MAX78000/EvKit_V1/board.mk

@@ -67,6 +67,10 @@ PROJ_CFLAGS+=-DCAMERA_HM0360_COLOR
 else ifeq "$(CAMERA)" "OV5642"
 SRCS += ov5642.c
 PROJ_CFLAGS+=-DCAMERA_OV5642
+else ifeq "$(CAMERA)" "OV5640"
+SRCS += ov5640.c
+PROJ_CFLAGS+=-DCAMERA_OV5640
+PROJ_CFLAGS+=-DOV5640_DVP
 else ifeq "$(CAMERA)" "OV7692"
 SRCS += ov7692.c
 PROJ_CFLAGS+=-DCAMERA_OV7692

Libraries/MiscDrivers/Camera/camera.c

@@ -788,7 +788,7 @@ int camera_setup_tft(int xres, int yres, pixformat_t pixformat, fifomode_t fifo_
 #endif
 
 #if defined(CAMERA_HM01B0) || defined(CAMERA_HM0360_MONO) || defined(CAMERA_HM0360_COLOR) || \
-    defined(CAMERA_OV5642)
+    defined(CAMERA_OV5642) || defined(CAMERA_OV5640)
 int camera_read_reg(uint16_t reg_addr, uint8_t *reg_data)
 {
     return camera.read_reg(reg_addr, reg_data);

Libraries/MiscDrivers/Camera/camera.h

@@ -46,6 +46,8 @@
 #include "hm0360_regs.h"
 #elif defined(CAMERA_OV5642)
 #include "ov5642_regs.h"
+#elif defined(CAMERA_OV5640)
+#include "ov5640_regs.h"
 #elif defined(CAMERA_OV7692)
 #include "ov7692_regs.h"
 #elif defined(CAMERA_PAG7920)
@@ -100,7 +102,7 @@ typedef struct _camera {
     int (*reset)(void);
     int (*sleep)(int enable);
 #if defined(CAMERA_HM01B0) || (CAMERA_HM0360_MONO) || (CAMERA_HM0360_COLOR) || \
-    defined(CAMERA_OV5642)
+    defined(CAMERA_OV5642) || defined(CAMERA_OV5640)
     int (*read_reg)(uint16_t reg_addr, uint8_t *reg_data);
     int (*write_reg)(uint16_t reg_addr, uint8_t reg_data);
 #else //(CAMERA_OV7692) || (CAMERA_PAG7920)
@@ -153,7 +155,7 @@ int camera_sleep(int enable);
 int camera_shutdown(int enable);
 
 #if defined(CAMERA_HM01B0) || (CAMERA_HM0360_MONO) || (CAMERA_HM0360_COLOR) || \
-    defined(CAMERA_OV5642)
+    defined(CAMERA_OV5642) || defined(CAMERA_OV5640)
 // Write a sensor register.
 int camera_write_reg(uint16_t reg_addr, uint8_t reg_data);
 int camera_read_reg(uint16_t reg_addr, uint8_t *reg_data);

Libraries/MiscDrivers/Camera/mipi_camera.h

@@ -35,8 +35,9 @@
 #define LIBRARIES_MISCDRIVERS_CAMERA_MIPI_CAMERA_H_
 
 #include <stdint.h>
+#ifndef OV5640_DVP
 #include "csi2.h"
-
+#endif
 /**
  * @brief Pixel format enumerations.
 */
@@ -89,12 +90,15 @@ typedef struct _mipi_camera_format {
  * @brief Camera settings struct.  This is the "top-level" configuration struct
  * encapsulating all camera settings.  Pass this in to the @ref mipi_camera_init function.
 */
+
 typedef struct _mipi_camera_settings_t {
     unsigned int width; /**< Image width in pixels */
     unsigned int height; /**< Image height in pixels */
     mipi_camera_format_t camera_format; /**< Image format */
+#ifndef OV5640_DVP
     mxc_csi2_line_handler_cb_t
         line_handler; /**< Line handler provided by application to process incoming camera data */
+#endif
 } mipi_camera_settings_t;
 
 typedef enum {
@@ -208,8 +212,9 @@ mipi_camera_settings_t mipi_camera_get_camera_settings(void);
  * @brief Get detailed statistics about the last image capture and any errors that occurred.
  * @return A @ref mxc_csi2_capture_stats_t struct
  */
+#ifndef OV5640_DVP
 mxc_csi2_capture_stats_t mipi_camera_get_capture_stats(void);
-
+#endif
 /**
  * @brief Parse a string containing information about the last captured image.
  * This is used with console.py utilities.