Discussions

• 1 You must be logged in to vote

  🙏

  What is your email address? I sincerely request to collaborate with you again, as I need to communicate with you.

  hanke-cnc asked Nov 8, 2024 in Q&A · Unanswered

  

  

  13
• 1 You must be logged in to vote

  💬

  using with esp8266

  assegid started Oct 24, 2024 in General

  

  

  25
• 1 You must be logged in to vote

  🔧

  STM32F4-SKR-Pro-V1_2 Compile Error

  landtree asked Aug 2, 2024 in Config and issues · Answered

  

  

  107
• 1 You must be logged in to vote

  🙏

  Advice re ESTOP, FHOLD, CS_RES = GRBL/CNCShield Abort, Hold, Resume

  hmmueller asked Aug 3, 2024 in Q&A · Answered

  

  

  5
• 1 You must be logged in to vote

  🙏

  Question re end switch (reset) behavior

  hmmueller asked Aug 3, 2024 in Q&A · Answered

  

  

  4
• 1 You must be logged in to vote

  🙏

  Getting µCNC master up and running - problems

  hmmueller asked Jul 28, 2024 in Q&A · Answered

  

  

  5
• 1 You must be logged in to vote

  🙏

  PlatformIO and Arduino Uno - it wants to upload to many other boards?

  hmmueller asked Jul 28, 2024 in Q&A · Answered

  

  

  3
• 1 You must be logged in to vote

  🙏

  Fundamental problems with 1.6.2

  hmmueller asked Jul 28, 2024 in Q&A · Closed · Answered

  

  

  2
• 1 You must be logged in to vote

  🙏

  ESTOP: uCNC "pin" vs. pin on Arduino board vs. pin on CNC Shield V.3 - a documentation question

  hmmueller asked Jul 28, 2024 in Q&A · Answered

  

  

  2
• 1 You must be logged in to vote

  🙏

  Support for MKS DLC32 2.1

  padcom asked Jul 13, 2024 in Q&A · Answered

  

  

  1
• 1 You must be logged in to vote

  🙏

  6-Axis configuration with CORE-BC kinematics

  alexmnr asked Mar 25, 2024 in Q&A · Answered

  

  

  2
• 1 You must be logged in to vote

  🙏

  PWM Laser or PPI Laser

  andy0983 asked Mar 5, 2024 in Q&A · Unanswered

  

  

  9
• 1 You must be logged in to vote

  🔧

  Homing and limit switches

  andeksan asked Feb 27, 2024 in Config and issues · Answered

  

  

  7
• 1 You must be logged in to vote

  🙏

  Newbie Question: Scara kinematic choppy movement

  Anno2003 asked Feb 22, 2024 in Q&A · Answered

  

  

  6
• 1 You must be logged in to vote

  💬

  Rotation aix for cartesian kinematic

  andeksan started Feb 13, 2024 in General

  

  

  5
• 1 You must be logged in to vote

  🔧

  If I start the spindle, ALARM:13 is displayed

  question question

  andy0983 asked Jan 31, 2024 in Config and issues · Answered

  

  

  2
• 1 You must be logged in to vote

  💬

  uCNC on Arduino Uno with CNC Shield V3

  timint started May 9, 2023 in General

  

  

  

  

  24
• 1 You must be logged in to vote

  💬

  Newbie question: Cannot connect (from UGS or Arduino IDE serial monitor)

  hmmueller started Oct 28, 2023 in General

  

  

  8
• 1 You must be logged in to vote

  🔧

  Jog command from MEGA/RAMPS/Reprap Controller not working

  mvackel asked Oct 19, 2023 in Config and issues · Answered

  

  

  5
• 1 You must be logged in to vote

  💡

  74HC595 support for RP2040

  Hyakutake12 started Oct 20, 2023 in Ideas

  

  

  3
• 1 You must be logged in to vote

  🔧

  SET_ORIGIN_AT_HOME_POS and Soft Limits

  mvackel asked Oct 19, 2023 in Config and issues · Answered

  

  

  4
• 1 You must be logged in to vote

  💡

  G28/G28.1 vs G10 L2 P28

  mvackel started Oct 19, 2023 in Ideas

  

  

  3
• 1 You must be logged in to vote

  🔧

  Error message on UGS on Jog issued from controller

  mvackel asked Oct 1, 2023 in Config and issues · Answered

  

  

  7
• 1 You must be logged in to vote

  🔧

  RP2040 (Pi Pico) homing issue - Z stepper motor doesn't stop despite z limit switch trigger

  Hyakutake12 asked Oct 9, 2023 in Config and issues · Answered

  

  

  1
• 1 You must be logged in to vote

  🔧

  RP2040 (Pi Pico) limit switch input not reading, always shows high

  Hyakutake12 asked Oct 6, 2023 in Config and issues · Answered

  

  

  7