Skip to content

ThenTech/TTISD

 
 

Repository files navigation

TTISD

Bjorn Jorissen, William Thenaers


Assignment 1: Android geoTODO

Some screenshots from an emulator can be found in TTISDassignment1/doc/.

A video showing the execution on a real Android smart phone and a Samsung Gear Live is also inlcuded.

Assignment 2: Interactive Room

Some screenshots and a video can be found in TTISDassignment2/doc/.

A release build is provided in TTISDassignment2/bin/Release (after building). Running it might require the Kinect SDK (v1.8).

Gameplay

First, someone presses the Start Calibration button.

1_Start_info_screen

Four cyan square will appear in each corner of the game window. When starting calibration, only one will be shown at a time. The tracked skeleton position of one person will be shown on the left side of the above status window. The person should stand on a projected square, and pressing Lock Point will calibrate the game corner the person is standing on with their current Kinect skeleton position. After locking, the next square will be shown, until all points are locked.

1_Start_info_screen

After all four corners are calibrated, a second person can join the Kinect viewing range and when the two people are being tracked (both XYZ positional values are being updated in the status screen), someone can press play and the game will start.

The purpose of the game is gathering as many points as possible by destroying the blocks in the middle, and when they are destroyed, players must compete against each other to bring the other's score to 0. The last player with a score greater than 0 wins.

1_Start_info_screen

The colour of a block determines the score a player gets by destroying it (green gives 1 point, yellow 2, orange 3, up to magenta with 5 points). Hitting a block will transition it to a lower state, e.g. hitting a magenta block will give the player 5 points, then the block will turn red and will give 4 points on the next hit. A green block worth 1 point will disappear when hit.

The last player that touched the ball will get the points. If a ball reaches the left or right boundary on a player's side, 5 points will be deducted from that player and the ball's position and speed will reset to the side the ball was lost in. The ball will start moving towards the other side. When a player hits the ball, its speed will slightly increase, while hitting a block will reset the speed modifier.

If all blocks are destroyed and one player loses all his points, then the other player wins. If both players lose all their points (by not preventing a ball from reaching their border), the game ends in a draw as seen below.

1_Start_info_screen

Assignment 3: Gamepad controller

We made a game controller for Kerbal Space Program (KSP), with the following features:

  • Control your craft (pitch, yaw, roll) by moving the controller or the joystick around;
  • Adjust the thrust output (throttle);
  • Switch between motion or joystick control mode.

Enclosure outside

Code

The Microbit runs a simple main loop that collects data from each of the following inputs:

  • The joystick (analogue X/Y-axes) for pitch and roll control;
  • The Inertia Measurement Unit (analogue X/Y/Z-axes) for pitch and roll control;
  • Two trigger buttons for yaw controll;
  • A linear potentiometer for amount of thrust;
  • A switch to toggle joystick or IMU control mode.

Since the assignment required Python, both the Microbit and the host computer run a script, Code/KSPCommander_device.py and Code/KSPCommander_host.py respectively. Installing the PySerial package on the host is required.

By using MicroPython on the Microbit, there is not enough memory left to use the full radio module for Bluetooth support, and hence we had to give up on using it. Since the working memory is also limited when using Python, the script had to be split between the Microbit and the host, else the entire interaction with the Microbit and KSP could have been contained on the Microbit only,

We used the KerbalSimpit mod (open source) and adapted its companion Arduino library for the Microbit. After handshaking, the mod handles packets sent from a serial port to adjust data in the game. Since the code could not be contained on just the Microbit, the additional host script requires an emulated COM port to communicate with KerbalSimpit. This is achieved with the external program com0com (install can be found in Code/deps).

Enclosure

Refer to the circuit diagram and the SVG drawing in the Enclosure folder.

Circuit diagram

The triggers are connected to the same pins as the on-circuit buttons A and B, and thus don't require an extra resistor. The mode switch does not require a resistor as well, because digitally read pins are automatically pulled down internally. So connecting to Vcc provides a clean reading. The other inputs are resistors themselves (stick and throttle slider) and are not pulled as they are analogue.

The enclosure was cut from a 2 mm MDF sheet. Both sides are living joints to provide a better grip when holding the controller.

The wiring is directly soldered to the extension board, covered with heat shrinks where applicable.

Enclosure insides

Gameplay

Before starting, check on which port the Microbit is connected and make sure to install com0com (the default COM to COM link is fine).

  1. Open KSPCommander_host.py and adjust the MicroPlayer arguments under __main__ accordingly:
    • device_serial_port should be the COM port where the Microbit is connected on;
    • ksp_serial_port should be one of the 2 virtual COM ports created with com0com.
  2. Install KSP and use CKAN (KSP mod manager) to install KerbalSimpit;
  3. Navigate to the KSP install folder and go to Kerbal Space Program\GameData\KerbalSimpit\PluginData. Rename Settings.cfg.sample to Settings.cfg and change the PortName variable to the other COM port from the virtual pair (as in the script uses one, and KerbalSimpit will use the other);
  4. Start KSP, plug the Microbit in the computer and start the host script;
  5. When ready, press both triggers on the controller at the same time, the host script will try to handshake with the mod. When this succeeds a message will be displayed in the console;
  6. Choose or build a vessel to fly and mod will use the data from the controller to override the keyboard controls. You can now control your flight with the controller!

A video showing the handshake setup and some gameplay can be found in Doc.

Project

Target scope

Our initial idea was to embed a board game with complex rules within a technological framework to decrease the knowledge needed to play the game. This framework could be used to play any similar board game, i.e. a game where a player's pawn moves over squares.

This framework would combine RFID tags to identify the used pawns and their positions and an addtional LIDAR to determine where it moved to. This idea evolved during our research and experiments, as we encountered some problems with our initial scope.

As an example, we provided a Monopoly game with a simplified rule set. The game itself is digital, but the board, pawns and dice are physical. The framework mentioned above would be used to determine the positions of each pawn and to detect and report if they moved.

Initial ideas

TTISD_Proposals

Multiple scanners

Our first idea was to work with multiple scanners arranged in a grid and RFID tags on every pawn on the board game. By using this approach, it would be possible to determine the exact position of a tag by measuring the time it took to read it from multiple locations [ref]. This idea is not very cost-effective, as each position in the grid would need a separate antenna, RFID tag reader and MCU to control it.

Seeing as this would not be viable and because we where told there was a simultaneous RFID reader available that could read 100s of tags per second, we opted to try that instead, hence the second idea below.

Multiple tags with one scanner

Because the first idea was viable, we tried to use the SparkFun Simultaneous RFID Tag Reader instead. The board would now consist of a grid with an RFID tag at each position. Pawns would have some metallic or signal blocking material on their bottom, blocking out the tag underneath. This way, tags that can not be read, are tags containing a player's pawn. We tested how well this idea worked.

TTISD_Project_RFID_antenna

We started with the example code from the Arduino library (local, requires ArduinoSTL lib). The reader works to some extent when just reading tags that pass by the antenna (see TTISD-Project/Research/RFID/Arduino test sketches), but we never got a reliable readout. Example applications from other users show that the setup should be capable of detecting multiple tags that pass in front of the antenna, and fair enough if tags pass by, they get detected. But multiple UHF RFID tags resulted in a continuous bad CRC error when they are just held stationary in front of the antenna. Since our proposed application would require the detection of a grid of stationary tags, this method proved to fail our expectations.

A possible cause could be that these Ultra-High Frequency tags (UHF) are subject to interference with other tags or other UHF signal sources, although they are designed in a way the mitigates this problem. Another adjustment we tried, was providing the reader with an external power supply and increasing the signal strength. This however, yielded no better results than just using the usb powered Arduino. Experiments in the way the code handled reading tags were also in vain.

Most other applications are using this setup to detect items passing in front of the antenna and only needing to detect each unique tag once. When doing the same thing, we noticed that the tags were indeed read correctly. We concluded that the energy needed for a signal to read a tag is best transmitted and received if the tag is moving. As mentioned before, using this approach would result in a completely different game design, so we opted against it.

LIDAR

While working on the RFID tags we also experimented with a LIDAR sensor.

The Velodyne LIDAR that was available, has a minimum range of 1 meter and a maximum range of 100 meters. While this is good for outdoor applications, like tracking large environments which is what the LIDAR is designed for, it is overkill for the application we wanted to create. Apart from the high range, it can measure multiple vertical levels to create a 3D environment map. Example traces can be found in TTISD-Project/Research/LIDAR/Velodyne LIDAR (VeloView software required to read them).

Velondyne LIDAR trace

We were shown a paper that used a LIDAR sensor to identify objects and gestures, but as we wanted to use small pawns, this did not look applicable to our idea. It still consisted of combining a LIDAR with RFID tag tracking to create a board game.

The Velodyne LIDAR was far too expensive for use in a simple prototype game.

After some research, we found a valid alternative for our application: the Slamtec RPLIDAR A1 development kit. This sensor is commonly used for small autonomous robots and has a smaller range, from 20 cm to 10 m, and can only see in one plane. Using the accompanied SDK in Research/LIDAR/RPLIDAR/rplidar_sdk_v1.10.0, creating an integrated program proved easy. We modified the example frame_grabber program to include a segment matching algorithm. This can be found in Code/Deploy/frame_grabber.exe.

RPLIDAR_frame_grabber

After providing some settings like the amount of segments and the start and end distance to look in, the segmented circle as shown above can be drawn. We created some function so we could query which segments are detected, i.e. contain a pawn.

Monopoly

Because the method of using the RFID tag scanning proved not reliable enough for our needs, we decided to drop it and continue on working with the RPLIDAR. The resolution of the RPLIDAR is not high enough to accurately distinguish between individual pawn, so we decided on simplifying the game's design. The physical board would be a segmented circle like the frame_grabber example shown above, and the players would throw their dice and move their pawn on the board. After each turn, the LIDAR can detect the changes in detected segments and extrapolate how many spaces a pawn moved.

The game has to stay turn based to be able to track the current player's pawn, since no unique pawns can be seen by the LIDAR. The physical board should contain the segments as shown below, while the digital counterpart is used to keep track of the game state. When designing the board, we noticed that the actual minimum range the RPLIDAR could detect a point, started from 12 cm instead of the given 20 cm from the datasheet. This allowed us to make the board a bit more compact. The design for the board and pawns can be found in Design. These were cut and engraved into cardboard.

TTISD_Project_6_Game_board_top

Since the RPLIDAR driver is written in C++, we looked for a C++ based Monopoly game that we could adapt to our needs. We settled on using Andrew Chen's implementation based on the Qt framework for a GUI. After integrating the driver from the SDK, the resulting Monopoly game can be played with either the LIDAR sensor for determining the positions of pawns or with the integrated dice rolling logic. The code for this game can be found in Code/Monopoly-master. A deployed build can be found in Code/Deploy. Changes we made to this code are including the RPLIDAR driver and integrating the position query into the game, as well as a history feature so players can easily see what happened to them. Some visual improvements were also made, to improve the playing experience.

When starting the game, the user has to specify the settings to use. These are kept adjustable to prove that a framework can be build around the RPLIDAR driver to support any board game.

Driver settings

The minimum and maximum distance from the middle of the sensor can be configured manually or calibrated by putting a pawn at the desired distance. It is possible that the detection of the pawn in this stage fails (e.g. the distance in mm is not accurately measured and noticeably much too large to be the actual distance, but it should work fine after a few measurements). The points match threashold determines how many dots the RPLIDAR driver will consider inside a segment before marking it as detected (this can be tested with the frame_grabber program in the Boost scan mode).

After the driver has successfully initialised, the amount of players can be chosen, as well as which pawn they will use.

TTISD_Project_2_Game_player_config

TTISD_Project_3_Game_player_select

Each virtual icon has a corresponding physical pawn.

TTISD_Project_5_Game_pawns

After everything is done, the main game window will be shown and the game can begin.

TTISD_Project_8_Game_application

Each player rolls their dice and moved their pawn, turn by turn. After moving the pawn, the Rolled Dice and moved button should be pressed to advance the game. As mentioned before, the LIDAR will now detect the new game state and extrapolate the new position of the current player and update the virtual game board. When a player lands on a square that already has a pawn, he/she should move to the next one. This state cannot be handled as the pawn could have "disappeared" on any square that has a pawn and can therefore not be detected.

Refer to TTISD_Project_9_DemoFHD.mp4 for actual gameplay. We used a mobile app for rolling the dice, since we forgot to bring physical ones.

The game itself is not feature complete when compared to the official rules of Monopoly, but it works fine as a simplified version for our purposes. Our initial goal of creating a unified interface and provide a framework for playing (complex) board games virtually with a physical segmented board, is therefore not fully achieved, but we have shown that this approach is viable for future work.

Future work

  • Integrate multiple RPLIDARs with the same game, allowing remote play with others;
  • Continue extending the RPLIDAR driver to create a unified toolkit that can be included in other games and provides support for LIDAR positioning to the game. A way to change the settings for the used board is already provided. Another game could just change these and use the driver to be able to work with an RPLIDAR.
  • Add another way of tracking pawns to prevent cheating. Right now, a player could move his pawn backwards, resulting in having 'moved' across the entire board. Similarly, a player cannot be tracked if he moves to a square already containing a pawn, as the LIDAR cannot identify unique pawns.

Releases

No releases published

Packages

No packages published

Languages

  • C++ 90.0%
  • C 4.7%
  • C# 2.5%
  • Python 1.2%
  • Java 1.0%
  • Makefile 0.4%
  • Other 0.2%