-
Notifications
You must be signed in to change notification settings - Fork 309
Underlying proxy configuration guides
Cloak requires its underlying proxy software to route its traffic to and from Cloak client and server; this generally requires a minor reconfiguration to existing setups. This page covers OpenVPN, Shadowsocks and Tor. Any other proxy can be configured in similar fashions.
Since OpenVPN's configuration is quite complicated, it's preferable to first make sure OpenVPN is already working as intended before reconfiguring for Cloak
Make sure the following lines are in your .conf file
# So that OpenVPN is listening to ck-server
local 127.0.0.1
# UDP support is experimental at the moment. Change the line below to proto tcp if it's not working well
proto udp
dev tun
Take note of port, and set the same port number in openvpn's entry in Cloak server's ProxyBook. Depending on if you used proto udp or tcp, the ProxyBook entry needs to correspond to it.
You'll need to start ck-server with ck-server -c <path to Cloak server's config>
You must not leave EncryptionMethod as plain in Cloak client's configuration file because OpenVPN gives out fingerprint. Change it to aes-gcm or chacha20-poly1305
In your client side .ovpn (or .conf on Linux) file:
Make sure dev is set to tun, the same as the server side configuration
dev tun
Change the remote server to 127.0.0.1:1984 (unless you have changed the ck-client listening port to another port) like this
remote 127.0.0.1 1984
Then add a line so that the underlying connections between ck-client and ck-server can be sent through the physical interface, instead of being looped back by OpenVPN
route <actual IP of the remote server> 255.255.255.255 net_gateway
You'll need to start ck-client with ck-client -u -c <path to Cloak client's config> if you are using proto udp. Otherwise remove the -u flag: ck-client -c <path to Cloak client's config>
Cloak is compliant to the Shadowsocks SIP003 protocol. If the Shadowsocks version you are using supports plugin natively (such as shadowsocks-libev and Shadowsocks Windows), you can follow the plugin mode section; if it doesn't, you can follow the standalone section
In Shadowsocks' configuration file (located at /etc/shadowsocks-libev/config.json if you are using shadowsocks-libev), add the following entry:
"plugin": "<path to ck-server>",
"plugin_opts": "<path to ckserver.json>"
You only need to run ss-server. ck-server will be started automatically.
Do the same thing as server in the configuration file, except it's for ck-client. If you are using the Windows GUI client, set the Plugin Program to be the path to ck-client, and Plugin Options to be the path to ckclient.json.
ck-client will be started automatically by Shadowsocks. You can leave EncryptionMethod as plain since Shadowsocks already hides fingerprints.
In Shadowsocks' config.json, set server to "127.0.0.1". Take note of server_port and set the same port number in shadowsocks' entry in ProxyBook of Cloak server's config. Start shadowsocks server, then start ck-server separately with ck-server -c <path to Cloak server's config>
Set server's IP to 127.0.0.1, port to 1984 (unless you will changed this when you start ck-client with -l parameter). Start ck-client first with ck-client -c <path to Cloak client's config>, then start Shadowsocks.
You can leave EncryptionMethod as plain since Shadowsocks already hides fingerprints.
In the context of Tor, Cloak acts like a Tor bridge
Edit /etc/tor/torrc and add in the following lines:
SocksPort 0 # Optional. This just makes Tor stop listening as a local SOCKS proxy
BridgeRelay 1
ORPort 127.0.0.1:<port of choice>
# You may notice that you can put "NoAdvertise" after the ORPort entry thinking that this will stop tor from advertising your bridge; however if you do that, tor will refuse to start. Some how by design tor has to advertise itself when running as a relay. Though if you specify the listening address as 127.0.0.1, external machines can't connect to it.
Edit the ProxyBook entry for tor in Cloak server's config file so that the port you entered as ORPort is reflected in Cloak's config as well.
You'll need to start ck-server with ck-server -c <path to Cloak server's config>
You must not leave EncryptionMethod as plain in Cloak client's configuration file because Tor gives out fingerprint. Change it to aes-gcm or chacha20-poly1305
First you need to start ck-client with ck-client -c <path to Cloak client's config>
Open up and configure TorBrowser, tick "Tor is censored in my country" and then tick "Provide a bridge I know", type in 127.0.0.1:1984 (or another port if you have change the listening port with -l flag), and then connect.