Skip to content

glneo/tap-firmware

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

6 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

TAP

TAP Programmable LED Array

The TAP contains eight rows each made up of eight pixels which in turn consists of three individually controllable light emitting diodes, red, green and blue.

The Display

Electrically, the LEDs are arranged in a matrix of 24 columns by 8 rows. The columns are controlled by GPIO pins from the MSP430; a “1” on a column pin grounds its corresponding column. A “0” on a row pin ties the row to power. The rows pings are addressed using a shift register, at the start of a scan a "0" is shifted into the register and it is clocked once to send +5V to each subsequent row.

The Display Buffer

A display buffer consists of a two dimensional array of the desired intensities of the LEDs, each one ranging from 0 to 31(FULL_INTENSITY). Colors are stored in the column index and are in the order red, green, then blue. Generally, only a single display buffer is needed, namely 'display_buffer'. Constants are defined to facilitate direct access to the intensities. For example, the green LED of column 3 on row 2 (all zero based) can be addressed as follows: display_buffer[ROW2][COL3+GREEN]. The scanning engine is conceptually very simple. Each time scan_LEDs is called, it performs one scan of the LEDs, using the intensity values in the display buffer to turn on each LED for an appropriate amount of time.

USB Support

To configure for building without the USB subsystem, edit main.h to comment out the definition USB_SUPPORT.

Serial Ports

The MSP430F5510 microcontroller contains two serial input and output ports. TAP units have been designed to be plugged together to form a larger display panel. The B input port receives data from the adjacent unit to the left; the B output port sends data to the adjacent unit to the right. The A input port receives data from the adjacent unit below; the A output port sends data to the adjacent unit above.

We currently initialize the serial ports for 115200 baud. The hardware is capable of much higher data rates should it be needed for demanding amounts of binary image data.

Packet Forwarding

In order to form a large display panel from individual TAP units, we use a packet message communication system. The firmware has been designed to support assigning each unit a unique ID so that it can be directly addressed. For this mechanism to work, each TAP must pass packets through its serial ports. Packets are CRC checked.

Learn Mode

The command packet definition has provision to direct information to a single specific unit when several are connected together. Learn Mode is how to set this up. Generally, the unit in the lower left corner of the arrangement is assigned the address (0,0). The one to its right is (0,1), then (0,2), and so on. The unit above it is (1,0) and the units to that one’s right is (1,1) and so on.

Tap Synchronization

A special provision has been implemented in the standard firmware to allow easily synchronizing timing across multiple TAP units when forming a larger single display.

Source Code Organization

  • channel.c - Channel coding, common to all communication types, forwards to the packet decoder.

  • demo.c - Program containing the user program. (Put your application code here)

  • display.c - Display related code, handles reading from the display buffer and outputting to the LEDs

  • init.c - Manages the power-up reset process, setting up the clock and initializing the other subsystem.

  • main.c - The foundation of the firmware. Contains the main loop.

  • packet.c - Decoding and encoding of packets.

  • photo.c - Phototransister related setup and communication handling.

  • state.c - System state.

  • uart.c - UART related setup and communication handling.

  • usb.c - USB related setup and communication handling.

Math Library

At least one of the demo files makes use of a TI Math Library called IQMATHLIB. This library is not included in this repository. You can download and install this library from TI here: http://software-dl.ti.com/msp430/msp430_public_sw/mcu/msp430/IQmathLib/latest/index_FDS.html It is linked to this project in the code composer studio configuration file in it's default install location which is ${TI_PRODUCTS_DIR}/msp430/IQMATHLIB_01_10_00_05/ If your install directory is different or if you wish not to use this library and the demo files that make use of it you will need to modify the code composer studio configuration file accordingly.

About

No description, website, or topics provided.

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages