hal::k20: Add DSPI registers

src/hal/k20/mod.rs

@@ -19,3 +19,4 @@ pub mod sim;
 pub mod pin;
 pub mod uart;
 pub mod watchdog;
+pub mod spi;

src/hal/k20/spi.rs

@@ -0,0 +1,171 @@
+// Zinc, the bare metal stack for rust.
+// Copyright 2014 Ben Gamari <bgamari@gmail.com>
+//
+// Licensed under the Apache License, Version 2.0 (the "License");
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//
+//     http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+
+/*!
+SPI peripheral
+*/
+
+/// Registers
+pub mod reg {
+  use lib::volatile_cell::VolatileCell;
+  use core::ops::Drop;
+
+  ioregs!(DSPI = {
+    0x0     => reg32 mcr { //! Module configuration register
+      0      => halt,      //= Start/stop transfers
+      8..9   => smpl_pt {  //! How many clocks between SCK edge and SIN sample
+        0x0  => SMPL_PT_0_CLKS,
+        0x1  => SMPL_PT_1_CLKS,
+        0x2  => SMPL_PT_2_CLKS,
+      }
+      10     => clr_rxf,   //= Flush RX FIFO
+      11     => clr_txf,   //= Flush TX FIFO
+      12     => dis_rxf,   //= Disable receive FIFO
+      13     => dis_txf,   //= Disable transmit FIFO
+      14     => mdis,      //= Disable module
+      15     => doze,      //= Doze enable
+      16..20 => pcsis[5],  //= Chip select inactive states
+      24     => rooe,      //= Receive FIFO overflow overwrite enable
+      26     => mtfe,      //= Modified timing format enable
+      27     => frz,       //= Freeze
+      28..29 => dconf {    //! Peripheral configuration
+        0x0  => SPI,
+      }
+      30     => cont_scke, //= Continuous SCK enable
+      31     => mstr {     //! Master/slave mode select
+        0x0  => SLAVE,
+        0x1  => MASTER,
+      }
+    }
+
+    0x8     => reg32 tcr { //! Transfer count register
+      16..31 => tcnt,      //= Number of frames transmitted
+    }
+
+    0xc     => reg32 ctar[2] { //! Clock and transfer attributes
+      /// Baud rate scaler (master only)
+      ///
+      /// SCK baud rate = (f_sys / PBR) * (1 + DBR) / BR
+      0..3   => br,
+      /// Delay after transfer scaler (master only)
+      ///
+      /// t_delay = (1/f_sys) * PDT * DT
+      4..7   => dt,
+      /// After SCK delay scaler (master only)
+      ///
+      /// t_ASC = (1/f_sys) * PASC * ASC
+      8..11  => asc,
+      /// CS to SCK delay scaler (master only)
+      12..15 => cssck,
+      /// Baud rate prescaler (master only)
+      17..16 => pbr {
+        0x0  => PBR_2,
+        0x1  => PBR_3,
+        0x2  => PBR_5,
+        0x3  => PBR_7,
+      }
+      /// Delay after transfer prescaler (master only)
+      18..19 => pdt {
+        0x0  => PDT_2,
+        0x1  => PDT_3,
+        0x2  => PDT_5,
+        0x3  => PDT_7,
+      },
+      /// After SCK delay prescaler (master only)
+      20..21 => pasc {
+        0x0  => PASC_2,
+        0x1  => PASC_3,
+        0x2  => PASC_5,
+        0x3  => PASC_7,
+      },
+      /// CS to SCK delay prescaler (master only)
+      22..23 => pcssck {
+        0x0  => PCSSCK_2,
+        0x1  => PCSSCK_3,
+        0x2  => PCSSCK_5,
+        0x3  => PCSSCK_7,
+      },
+      /// Transfer LSB first (master only)
+      24     => lsbfe,
+      /// Clock phase
+      25     => cpha,
+      /// Clock polarity
+      26     => cpol,
+      /// Frame size
+      ///
+      /// Number of bits transferred per frame minus one.
+      /// In master mode the top bit of this field is the DBR, double
+      /// baud rate, flag
+      27..31 => fmsz,
+    }
+
+    0x2c    => reg32 sr {                 //! Status register
+      0..3   => popnxtptr,                //= Pop next pointer
+      4..7   => rxctr,                    //= RX FIFO counter
+      8..11  => txnxtptr,                 //= Transmit next pointer
+      12..15 => txctr,                    //= TX FIFO counter
+      17     => rfdf: set_to_clear,       //= Receive FIFO drain flag
+      19     => rfof: set_to_clear,       //= Receive FIFO overflow flag
+      25     => tfff: set_to_clear,       //= Transmit FIFO fill flag
+      27     => tfuf: set_to_clear,       //= Transmit FIFO underflow flag
+      28     => eoqf: set_to_clear,       //= End of queue flag
+      30     => rxrxs: set_to_clear,      //= TX/RX running
+      31     => tcf: set_to_clear,        //= Transfer complete flag
+    }
+
+    0x30    => reg32 rser {     //! DMA/interrupt request select and enable
+      /// Receive FIFO drain DMA/interrupt request select
+      16     => rfdf_dirs {
+        0x0  => RFDF_IRQ,
+        0x1  => RFDF_DMA,
+      }
+      17     => rfdf_re,        //= Recieve FIFO drain request enable
+      19     => rfof_re,        //= Receive FIFO overflow request enable
+      /// Transmit FIFO fill DMA/interrupt request select
+      24     => tfff_dirs {
+        0x0  => TFFF_IRQ,
+        0x1  => TFFF_DMA,
+      }
+      25     => tfff_re,        //= Transmit FIFO fill request enable
+      27     => tfuf_re,        //= Transmit FIFO underflow request enable
+      28     => eoqf_re,        //= End of Queue request enable
+      31     => tcf_re,         //= Transmission complete request enable
+    }
+
+    0x34    => reg32 pushr {    //! TX FIFO register
+      0..15  => txdata,         //= Transmitted data
+      16..21 => pcs[6],         //= Chip select state (master only)
+      /// Clear transfer counter (`TCR.TCNT`) (master only)
+      26     => ctcnt,
+      /// Set End of Queue flag (`SR.EOQF`) at end of transfer (master only)
+      27     => eoq,
+      28..30 => ctas,           //= CTAR select (master only)
+      31     => cont,           //= Continuous CS enable (master only)
+    }
+
+    0x38    => reg32 popr {     //! RX FIFO register
+      0..31  => rxdata: ro,     //= Received data
+    }
+
+    0x3c    => reg32 txfr[4] {  //! TX FIFO debug registers
+      0..15  => txdata: ro,
+      16..31 => txcmd_txdata: ro,
+    }
+
+    0x7c    => reg32 rxfr[4] {  //! RX FIFO debug registers
+      0..31  => rxdata: ro,
+    }
+  })
+}