Skip to content

jdelfes/nrf24le1_flasher

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

3 Commits
 
 
 
 
 
 
 
 

Repository files navigation

nRF24LE1 Flasher

This software is used to read, write or erase flash memory of Nordic nRF24LE1 chips. Product information can be found at Nordic site. If you are looking for a free SDK to programming that chip, you can find a good one from Brennen at his blog

Right now, we are using a FTDI FT232R serial<->usb chip to send SPI commands to nRF24LE1. But it's very simple to port to another platforms like Raspberry PI, Beaglebone etc. Product information can be found at ftdi site.

nRF24LE1 pinout

The pinout of this product it's very dependent of your manufacturer design, but the common ones on chinese sites are the 24 pins format with pins like this:

Left pins Right pins
3v3 P0.2 - FSCK
RESET P0.3 - FMOSI
RXEN P0.4 - FMISO
P0.0 P0.5 - FCSN
P0.1 P0.6
PROG GND

The 3v3 is the pin 1 (normally have a square around it).

If you have another design or chip version, please make sure you are following that pins (extracted from nRF24LE1 spec):

24pin-4x4 32pin-5x5 48pin-7x7
FCSN P0.5 P1.1 P2.0
FMISO P0.4 P1.0 P1.6
FMOSI P0.3 P0.7 P1.5
FSCK P0.2 P0.5 P1.2

FTDI FT232R

With this chip, we have 8 "GPIOs" to do a bitbang SPI implementation. You need to check if your breakout can configure to 3v3 operation. We hook each pin of nRF24LE1 on FT232R as described:

nRF24LE1 FT232R
FCSN RXD
FMISO RTS
FMOSI CTS
FSCK DTR
RESET DSR
PROG DCD
GND GND
3v3 VCCIO

Note that the pin FCSN is used as TX too, so we can hook RX on TXD of FT232R and we have serial already.

Dependencies

The only dependency is libftdi1 and libusb-1.0.

Usage

First hook all pins on nRF24LE1 and FT232R, so plug on USB and type on terminal:

$ lsusb -d 0403:6001

It will list every FTDI device connected at your PC, something like:

Bus 004 Device 048: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC 

If you see more that one entry, please go to "Multiple FTDI Devices" section.

You need permission to access that USB device. You can become root, use sudo or change permission of /dev/bus/usb/$BUS/$DEV specific.

The first task to do is a backup of your InfoPage!!!

# nrf24le1_flasher --read-ip ip_bkp.img

Just make sure that ip_bkp.img have 512 bytes, so you can save that file as your personal backup.

Now to write a new program:

# nrf24le1_flasher --erase-all --write-flash my_program.hex --write-ip ip_bkp.img

This command clear all memory, writes your program and restore your InfoPage that you saved before.

If you want to know other options, use the "--help" parameter.

Multiple FTDI Devices

If you have more than one FTDI plugged, you need to choose which one to be used. Type this command on terminal:

$ lsusb -t

It will list devices like:

/:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
    |__ Port 2: Dev 48, If 0, Class=Vendor Specific Class, Driver=ftdi_sio, 12M

Now we know the bus (4) and the port (2) of our FTDI device, so we can pass it to nrf24le1_flasher:

# nrf24le1_flasher -d 4-2 --read-ip ip_bkp.img

Another programmers/flashers

There are some options over there, like a kernel module from Eder, a Raspberry PI version from Derek and an Arduino programmer from Dean.

About

Flasher command for nRF24LE1 using FT232R

Topics

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published