※UARTtoPWMwith8bitsMCU

• Useing HT66F318 UART port access internal resource GPIO, LED matrix, EEPROM, ADC, I2C...(Same RS-485 driver)
  此專案利用PC軟件通過UART port下達指令以存取MCU內部的EEPROM(64bytes), PWM(10bits or 16bit) 都透過UART port
  

• Project Option:
  HXT (External 8MHz X'tal): 可選項有:HXT(400K~16Mhz),HIRC4M,HIRC8M,HIRC12M
  LICR (Low speed internal RC for TB0/TB1): 可選項有:LXT(32.768Khz),LIRC(32Khz)
  WatchDog: enable
  

• UART Baudrate: 9600,n,8,1 (協議格式參照RS-485通訊協議格式)
  

• TB0,1 enable LIRC interrupt for 0.514sec, 0.514sec
  

• TM0 enable HXT interrupt for 200us
  

• PWM輸出 PWM(HT66F317)設置直接透過TP0, TP1輸出, TM0/TM1(16bit), 最大設置TM0/TM1(16bit)
  PWM(HT66F318)設置直接透過TP0, TP1, TP2輸出, TM0(hi-16bit), 最大設置TM1(10bit), TM2(hi-16bit)
  

• HT-IDE3000 HT66F317/HT66F318 28ssop with HT-IDE3000 & e-Link & e-WriterPro
  文件HT66F318 Document
  模擬&除錯Development & DebugIDE3000 & ICE
  燒入器Progrmming & writerHOPE3000 & e-WriterPro
  

Relevant information

• HT-IDE3000 V8.02
• HOLTEK C Compiler V3/Assembly
• HT66F318 Config, used 8Mhz X'tal external, VDD/VDDA binding
• HT66F318 28ssop Schematic Diagram

How to test or used

利用PC通訊軟件做為主動工具, 協議(9600,n,8,1), 格式參照RS-485格式(PC指令CRC用 A0 0A代替CRC-16, MCU反饋的為真實CRC-16)

• For Example:

• UART Formate(Get from MCU): 44 03 00 00 00 04 A0 0A #讀取EEPROM位址0x0000,4組(共計8個bytes) MCU return設計最大每次讀取四組(8byte) 所以反饋時: 44 03 08 00 01 02 03 04 05 06 07 CRC CRC

• UART Formate(Write to MCU): 44 06 00 0A EE FF A0 0A #寫入EEPROM位址0x000A,資料為0xEEFF MCU return: 44 06 00 0A EE FF CRC CRC

• UART Formate(Write to MCU): 44 06 06 00 3F FF A0 0A #寫入PWM週期, 0x3FFF(TM1) is period (TM0,TM2 10bit) MCU return PWM: 44 06 06 00 3F FF CRC CRC

• UART Formate(Write to MCU): 44 06 06 01 2F FF A0 0A #寫入PWM佔比, 0x2FFF(TM1) is duty (TM0,TM2 10bit) MCU return PWM: 44 06 06 00 2F FF CRC CRC

Other applications

• UART access to ADC converter(HY3118 24bit ADC) via I2C bus.
• UART access to OLED 16x2 display driver via SPI bus.