Skip to content

Small python script for loading init.lua to ESP8266 nodemcu firmware

License

Notifications You must be signed in to change notification settings

marcoskirsch/luatool

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

23 Commits
 
 
 
 
 
 

Repository files navigation

luatool

###Tool for loading Lua-based scripts from file to ESP8266 with nodemcu firmware

###Summary

  • Allow easy uploading of any Lua-based script into the ESP8266 flash memory with NodeMcu firmware

###Requirements

python 2.7, pyserial (as for esptool)

###Discuss http://esp8266.ru

###Changelog v0.6.2

  • added support for nested strings
  • added check to verify the UART buffer will not overflow.

v0.6.1

  • put short versions of arguments back, see issue #2
  • flush serial port, fixes issue #1

v0.6

  • switched to argparse from getopts, renamed some arguments
  • removed call-home from main.lua
  • added --verbose option to show debugging
  • added comments, fixed some grammar, updated README
  • chmod 755'd the script so its runnable on POSIX
  • checked with nodemcu 0.9.4 20141222

v0.5

  • add new option -r, --restart : auto restart module, send command "node.restart()", after file load
  • add new option -d, --dofile : auto run, send command "dofile('file')", after file load
  • delete line "lua script loaded by luatool" for correct line number, lines number now equal lines number in original file
  • add 0.3 sec delay after write

v0.4

  • now check proper answer from NodeMCU after send data. After send string we expect echo line, if not got it, then error message displayed "Error sending data to LuaMCU"
  • if lua interpreter error received, then error message displayed "ERROR from LUA interpreter lua:..."
  • add heap info and chip id to example file init.lua
  • some changes in example file main.lua

###Run

####Typical use:

Edit file init.lua and set SSID and MasterPassword Then disconnect any terminal programm, and at command prompt type

./luatool.py --port /dev/ttyUSB0 --src init.lua --dest init.lua --verbose

Downloader start
Set timeout 3
Set interCharTimeout 3
Stage 1. Deleting old file from flash memory
->file.remove("init.lua") -> ok
.....................................
->file.close() -> ok
--->>> All done <<<---

./luatool.py

->file.open("main.lua", "w") -> ok
->file.close() -> ok
->file.remove("main.lua") -> ok
->file.open("main.lua", "w+") -> ok
->file.writeline([[tmr.alarm(0, 1000, 1, function()]]) -> ok
->file.writeline([[if wifi.sta.getip() == nil then]]) -> ok
->file.writeline([[print("Connecting to AP...")]]) -> ok
->file.writeline([[else]]) -> ok
->file.writeline([[print('IP: ',wifi.sta.getip())]]) -> ok
->file.writeline([[tmr.stop(0)]]) -> ok
->file.writeline([[end]]) -> ok
->file.writeline([[end)]]) -> ok
->file.flush() -> ok
->file.close() -> ok
--->>> All done <<<---

Connect you terminal program and send command (or you can use --restart option, when loading file init.lua)

node.restart()

after reboot:

lua script loaded by luatool 0.4
init.lua ver 1.2
set mode=STATION (mode=1)
MAC: 	18-FE-34-98-D4-B5
chip: 	10015925
heap: 	18464
set wifi
NodeMcu 0.9.2 build 20141125  powered by Lua 5.1.4

send command (or you can use --dofile option, when loading file main.lua)

dofile("main.lua")

connects to your AP and displays MCU's IP address

> dofile("main.lua")
> IP:   192.168.1.99

####Examples:

./luatool.py --port COM4 --src file.lua --dest main.lua --baud 9600
  • --port - COM1-COM128, default /dev/ttyUSB0
  • --baud - baud rate, default 9600
  • --src - source disk file, default main.lua
  • --dest - destination flash file, default main.lua

If use --dest option with parameter "init.lua" - autostart init.lua after boot. Be carefully about bugs in lua-script - may cause a boot loop. Use this option after full testing only.

Running without any parameters: load file "main.lua" via port /dev/ttyUSB0:9600 and place code into "main.lua" file into flash.

./luatool.py

after loading file to flash you can connect any terminal programm to ESP8266 and type:

dofile("main.lua") 

for executing you lua script

If you want load and autoexecute file main.lua, command dofile("main.lua"), you can use --dofile option

./luatool.py --dofile

Typically, place wifi.setmode, wifi.sta.config commands to init.lua file for connecting to you AP with low risk of boot loop, and other code place to main.lua for manually start and debug.

About

Small python script for loading init.lua to ESP8266 nodemcu firmware

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • Python 92.8%
  • Lua 7.2%