[Keyboard] Add Nuphy Air60 v2 keyboard

keyboards/nuphy/air60_v2/ansi/ansi.h

@@ -0,0 +1,177 @@
+/*
+Copyright 2023 @ Nuphy <https://nuphy.com/>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "quantum.h"
+
+enum custom_keycodes {
+    RF_DFU = QK_KB_0,
+    LNK_USB,
+    LNK_RF,
+    LNK_BLE1,
+    LNK_BLE2,
+    LNK_BLE3,
+
+    MAC_TASK,
+    MAC_SEARCH,
+    MAC_VOICE,
+    MAC_CONSOLE,
+    MAC_DND,
+    MAC_PRT,
+    MAC_PRTA,
+
+    SIDE_VAI,
+    SIDE_VAD,
+    SIDE_MOD,
+    SIDE_HUI,
+    SIDE_SPI,
+    SIDE_SPD,
+
+    DEV_RESET,
+    SLEEP_MODE,
+    BAT_SHOW,
+    RGB_TEST,
+    SHIFT_GRV,
+    BAT_NUM
+};
+
+
+typedef enum {
+    RX_Idle,
+    RX_Receiving,
+    RX_Done,
+    RX_Fail,
+    RX_OV_ERR,
+    RX_SUM_ERR,
+    RX_CMD_ERR,
+    RX_DATA_ERR,
+    RX_DATA_OV,
+    RX_FORMAT_ERR,
+
+    TX_OK = 0XE0,
+    TX_DONE,
+    TX_BUSY,
+    TX_TIMEOUT,
+    TX_DATA_ERR,
+
+} TYPE_RX_STATE;
+
+
+#define RF_LONG_PRESS_DELAY   30
+#define DEV_RESET_PRESS_DELAY 30
+#define RGB_TEST_PRESS_DELAY  30
+
+
+#define UART_HEAD           0x5A
+#define FUNC_VALID_LEN      32
+
+#define RF_IDLE             0
+#define RF_PAIRING          1
+#define RF_LINKING          2
+#define RF_CONNECT          3
+#define RF_DISCONNECT       4
+#define RF_SLEEP            5
+#define RF_SNIF             6
+#define RF_INVAILD          0XFE
+#define RF_ERR_STATE        0XFF
+
+#define CMD_POWER_UP     0XF0
+#define CMD_SLEEP        0XF1
+#define CMD_HAND         0XF2
+#define CMD_SNIF         0XF3
+#define CMD_24G_SUSPEND  0XF4
+#define CMD_IDLE_EXIT    0XFE
+
+#define CMD_RPT_MS       0XE0
+#define CMD_RPT_BYTE_KB  0XE1
+#define CMD_RPT_BIT_KB   0XE2
+#define CMD_RPT_CONSUME  0XE3
+#define CMD_RPT_SYS      0XE4
+
+#define CMD_SET_LINK     0XC0
+#define CMD_SET_CONFIG   0XC1
+#define CMD_GET_CONFIG   0XC2
+#define CMD_SET_NAME     0XC3
+#define CMD_GET_NAME     0XC4
+#define CMD_CLR_DEVICE   0XC5
+#define CMD_NEW_ADV      0XC7
+#define CMD_RF_STS_SYSC  0XC9
+#define CMD_SET_24G_NAME 0XCA
+#define CMD_GO_TEST      0XCF
+
+#define CMD_RF_DFU       0XB1
+
+#define CMD_WRITE_DATA   0X80
+#define CMD_READ_DATA    0X81
+
+
+#define LINK_RF_24       0
+#define LINK_BT_1        1
+#define LINK_BT_2        2
+#define LINK_BT_3        3
+#define LINK_USB         4
+
+#define UART_MAX_LEN     64
+typedef struct
+{
+    uint8_t RXDState;
+    uint8_t RXDLen;
+    uint8_t RXDOverTime;
+    uint8_t TXDLenBack;
+    uint8_t TXDOffset;
+    uint8_t TXDBuf[UART_MAX_LEN];
+    uint8_t RXDBuf[UART_MAX_LEN];
+} USART_MGR_STRUCT;
+
+typedef struct
+{
+    uint8_t link_mode;
+    uint8_t rf_channel;
+    uint8_t ble_channel;
+    uint8_t rf_state;
+    uint8_t rf_charge;
+    uint8_t rf_led;
+    uint8_t rf_baterry;
+    uint8_t sys_sw_state;
+} DEV_INFO_STRUCT;
+
+
+#define SYS_SW_WIN        0xa1
+#define SYS_SW_MAC        0xa2
+
+#define RF_LINK_SHOW_TIME 300
+
+#define HOST_USB_TYPE     0
+#define HOST_BLE_TYPE     1
+#define HOST_RF_TYPE      2
+
+#define LINK_TIMEOUT     (uint16_t)(100 * 120)
+#define SLEEP_TIME_DELAY (uint16_t)(100 * 360)
+#define POWER_DOWN_DELAY (uint16_t)(24)
+
+typedef struct
+{
+    uint8_t default_brightness_flag;
+    uint8_t ee_side_mode;
+    uint8_t ee_side_light;
+    uint8_t ee_side_speed;
+    uint8_t ee_side_rgb;
+    uint8_t ee_side_colour;
+    uint8_t sleep_enable;
+    uint8_t retain2;
+} user_config_t;

keyboards/nuphy/air60_v2/ansi/config.h

@@ -0,0 +1,80 @@
+/*
+Copyright 2023 @ Nuphy <https://nuphy.com/>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#define TAP_CODE_DELAY              8
+#define DYNAMIC_KEYMAP_MACRO_DELAY  8
+#define EECONFIG_USER_DATA_SIZE     8
+
+#define DEV_MODE_PIN                C0
+#define SYS_MODE_PIN                C1
+#define DC_BOOST_PIN                C2
+#define NRF_RESET_PIN               B4
+#define NRF_BOOT_PIN                B5
+#define NRF_WAKEUP_PIN              C4
+
+#define RGB_DRIVER_SDB1             C6
+#define RGB_DRIVER_SDB2             C7
+
+#define SERIAL_DRIVER               SD1
+#define SD1_TX_PIN                  B6
+#define SD1_TX_PAL_MODE             0
+#define SD1_RX_PIN                  B7
+#define SD1_RX_PAL_MODE             0
+
+
+// This is a 7-bit address, that gets left-shifted and bit 0
+// set to 0 for write, 1 for read (as per I2C protocol)
+// The address will vary depending on your wiring:
+// 0b1110100 AD <-> GND
+// 0b1110111 AD <-> VCC
+// 0b1110101 AD <-> SCL
+// 0b1110110 AD <-> SDA
+#define DRIVER_ADDR_1              0b1010000
+#define DRIVER_ADDR_2              0b1010011
+#define ISSI_TIMEOUT               1
+
+#define I2C_DRIVER                 I2CD1
+#define I2C1_SCL_PIN               B8
+#define I2C1_SDA_PIN               B9
+#define I2C1_CLOCK_SPEED           1000000
+
+#define I2C1_SCL_PAL_MODE          1
+#define I2C1_SDA_PAL_MODE          1
+
+#define I2C1_TIMINGR_PRESC         0U
+#define I2C1_TIMINGR_SCLDEL        0U
+#define I2C1_TIMINGR_SDADEL        0U
+#define I2C1_TIMINGR_SCLH          0U
+#define I2C1_TIMINGR_SCLL          0U
+#define I2C1_DUTY_CYCLE            FAST_DUTY_CYCLE_16_9
+
+
+#define DRIVER_COUNT               2
+#define DRIVER_1_LED_TOTAL         48
+#define DRIVER_2_LED_TOTAL         (16 + 10)
+#define RGB_MATRIX_LED_COUNT       (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)
+
+#define RGB_MATRIX_DEFAULT_MODE    RGB_MATRIX_CYCLE_LEFT_RIGHT  // Sets the default mode, if none has been set
+#define RGB_DISABLE_WHEN_USB_SUSPENDED                          // turn off effects when suspended
+
+#define RGB_MATRIX_FRAMEBUFFER_EFFECTS
+#define RGB_MATRIX_KEYPRESSES
+#define RGB_MATRIX_KEYRELEASES
+
+

keyboards/nuphy/air60_v2/ansi/halconf.h

@@ -0,0 +1,28 @@
+/*
+Copyright 2023 @ Nuphy <https://nuphy.com/>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include_next <halconf.h>
+
+#undef HAL_USE_SERIAL
+#define HAL_USE_SERIAL TRUE
+
+#undef HAL_USE_I2C
+#define HAL_USE_I2C TRUE
+
+