boards: fysetc: add FYSETC UCAN USB to CAN 2.0B adapter board

boards/fysetc/index.rst

@@ -0,0 +1,10 @@
+.. _boards-fysetc:
+
+FYSETC
+######
+
+.. toctree::
+   :maxdepth: 1
+   :glob:
+
+   **/*

boards/fysetc/ucan/Kconfig.ucan

@@ -0,0 +1,5 @@
+# Copyright (c) 2024 Henrik Brix Andersen <henrik@brixandersen.dk>
+# SPDX-License-Identifier: Apache-2.0
+
+config BOARD_UCAN
+	select SOC_STM32F072XB

boards/fysetc/ucan/board.cmake

@@ -0,0 +1,8 @@
+# Copyright (c) 2024 Henrik Brix Andersen <henrik@brixandersen.dk>
+# SPDX-License-Identifier: Apache-2.0
+
+board_runner_args(dfu-util "--pid=0483:df11" "--alt=0" "--dfuse")
+board_runner_args(jlink "--device=STM32F072CB")
+
+include(${ZEPHYR_BASE}/boards/common/dfu-util.board.cmake)
+include(${ZEPHYR_BASE}/boards/common/jlink.board.cmake)

boards/fysetc/ucan/board.yml

@@ -0,0 +1,6 @@
+board:
+  name: ucan
+  full_name: UCAN
+  vendor: fysetc
+  socs:
+    - name: stm32f072xb

boards/fysetc/ucan/doc/index.rst

@@ -0,0 +1,71 @@
+.. zephyr:board:: ucan
+
+Overview
+********
+
+The FYSETC UCAN is an open-source USB to CAN 2.0B adapter board. More information can be found on
+the `UCAN website`_ and in the `UCAN wiki`_.
+
+Hardware
+********
+
+The UCAN board is equipped with a STM32F072CB microcontroller and features an USB-C connector, a
+terminal block for connecting to the CAN bus, and two user LEDs. Schematics and component placement
+drawings are available in the `UCAN GitHub repository`_.
+
+Supported Features
+==================
+
+The ``ucan`` board configuration supports the following hardware features:
+
++-----------+------------+-------------------------------------+
+| Interface | Controller | Driver/Component                    |
++===========+============+=====================================+
+| NVIC      | on-chip    | nested vector interrupt controller  |
++-----------+------------+-------------------------------------+
+| PINMUX    | on-chip    | pinmux                              |
++-----------+------------+-------------------------------------+
+| FLASH     | on-chip    | flash memory                        |
++-----------+------------+-------------------------------------+
+| GPIO      | on-chip    | gpio                                |
++-----------+------------+-------------------------------------+
+| USB       | on-chip    | USB                                 |
++-----------+------------+-------------------------------------+
+| CAN1      | on-chip    | CAN controller                      |
++-----------+------------+-------------------------------------+
+
+The default configuration can be found in the defconfig file:
+:zephyr_file:`boards/fysetc/ucan/ucan_defconfig`.
+
+Other hardware features are not currently supported by the port.
+
+System Clock
+============
+
+The STM32F072CB PLL is driven by an external crystal oscillator (HSE) running at 8 MHz and
+configured to provide a system clock of 48 MHz.
+
+Programming and Debugging
+*************************
+
+Build and flash applications as usual (see :ref:`build_an_application` and
+:ref:`application_run` for more details).
+
+If flashing via USB DFU, short pins ``B0`` and ``3V3`` when applying power to the UCAN board in
+order to enter the built-in DFU mode.
+
+Here is an example for the :zephyr:code-sample:`blinky` application.
+
+.. zephyr-app-commands::
+   :zephyr-app: samples/basic/blinky
+   :board: ucan
+   :goals: flash
+
+.. _UCAN website:
+   https://www.fysetc.com/products/fysetc-ucan-board
+
+.. _UCAN wiki:
+   https://wiki.fysetc.com/UCAN/
+
+.. _UCAN GitHub repository:
+   https://github.com/FYSETC/UCAN/

boards/fysetc/ucan/ucan.dts

@@ -0,0 +1,96 @@
+/*
+ * Copyright (c) 2024 Henrik Brix Andersen <henrik@brixandersen.dk>
+ *
+ *  SPDX-License-Identifier: Apache-2.0
+ */
+
+/dts-v1/;
+
+#include <st/f0/stm32f072Xb.dtsi>
+#include <st/f0/stm32f072c(8-b)tx-pinctrl.dtsi>
+
+/ {
+	model = "FYSETC UCAN board";
+	compatible = "fysetc,ucan";
+
+	chosen {
+		zephyr,sram = &sram0;
+		zephyr,flash = &flash0;
+		zephyr,code-partition = &slot0_partition;
+		zephyr,canbus = &can1;
+	};
+
+	aliases {
+		led0 = &led_rx;
+		led1 = &led_tx;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led_rx: led_rx {
+			gpios = <&gpioa 0 GPIO_ACTIVE_HIGH>;
+			label = "LED RX";
+		};
+		led_tx: led_tx {
+			gpios = <&gpioa 1 GPIO_ACTIVE_HIGH>;
+			label = "LED TX";
+		};
+	};
+
+	transceiver0: can-phy0 {
+		compatible = "can-transceiver-gpio";
+		enable-gpios = <&gpioc 13 GPIO_ACTIVE_LOW>;
+		max-bitrate = <1000000>;
+		#phy-cells = <0>;
+	};
+};
+
+&clk_hse {
+	status = "okay";
+	clock-frequency = <DT_FREQ_M(8)>;
+};
+
+&pll {
+	prediv = <1>;
+	mul = <6>;
+	clocks = <&clk_hse>;
+	status = "okay";
+};
+
+&rcc {
+	clocks = <&pll>;
+	clock-frequency = <DT_FREQ_M(48)>;
+	ahb-prescaler = <1>;
+	apb1-prescaler = <1>;
+};
+
+zephyr_udc0: &usb {
+	pinctrl-0 = <&usb_dm_pa11 &usb_dp_pa12>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-0 = <&can_rx_pb8 &can_tx_pb9>;
+	pinctrl-names = "default";
+	phys = <&transceiver0>;
+	status = "okay";
+};
+
+&flash0 {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		boot_partition: partition@0 {
+			label = "mcuboot";
+			reg = <0x00000000 DT_SIZE_K(48)>;
+			read-only;
+		};
+		slot0_partition: partition@c000 {
+			label = "image-0";
+			reg = <0x0000c000 DT_SIZE_K(80)>;
+		};
+	};
+};

boards/fysetc/ucan/ucan.yaml

@@ -0,0 +1,15 @@
+identifier: ucan
+name: FYSETC UCAN
+type: mcu
+arch: arm
+toolchain:
+  - zephyr
+  - gnuarmemb
+ram: 16
+flash: 128
+supported:
+  - can
+  - gpio
+  - usb_device
+  - usbd
+vendor: fysetc

boards/fysetc/ucan/ucan_defconfig

@@ -0,0 +1 @@
+CONFIG_GPIO=y

dts/bindings/vendor-prefixes.txt

@@ -248,6 +248,7 @@ fsl	Freescale Semiconductor
 ftdi	Future Technology Devices International Ltd.
 fujitsu	Fujitsu Ltd.
 futaba	Futaba Corporation
+fysetc	Shenzhen Fuyuansheng Electronic Technology Co., Ltd.
 gaisler	Gaisler
 galaxycore	Galaxycore, Inc.
 gardena	GARDENA GmbH