-
Notifications
You must be signed in to change notification settings - Fork 97
SYSCALL
SYSCALL — Fast System Call
| Opcode | Instruction | Op/ En | 64-Bit Mode | Compat/ Leg Mode | Description |
| 0F 05 | SYSCALL | ZO | Valid | Invalid | Fast call to privilege level 0 system procedures. |
| Op/En | Operand 1 | Operand 2 | Operand 3 | Operand 4 |
| ZO | NA | NA | NA | NA |
SYSCALL invokes an OS system-call handler at privilege level 0. It does so by loading RIP from the IA32_LSTAR MSR (after saving the address of the instruction following SYSCALL into RCX). (The WRMSR instruction ensures that the IA32_LSTAR MSR always contain a canonical address.)
SYSCALL also saves RFLAGS into R11 and then masks RFLAGS using the IA32_FMASK MSR (MSR address C0000084H); specifically, the processor clears in RFLAGS every bit corresponding to a bit that is set in the IA32_FMASK MSR.
SYSCALL loads the CS and SS selectors with values derived from bits 47:32 of the IA32_STAR MSR. However, the CS and SS descriptor caches are not loaded from the descriptors (in GDT or LDT) referenced by those selectors. Instead, the descriptor caches are loaded with fixed values. See the Operation section for details. It is the respon- sibility of OS software to ensure that the descriptors (in GDT or LDT) referenced by those selector values corre- spond to the fixed values loaded into the descriptor caches; the SYSCALL instruction does not ensure this correspondence.
The SYSCALL instruction does not save the stack pointer (RSP). If the OS system-call handler will change the stack pointer, it is the responsibility of software to save the previous value of the stack pointer. This might be done prior to executing SYSCALL, with software restoring the stack pointer with the instruction following SYSCALL (which will be executed after SYSRET). Alternatively, the OS system-call handler may save the stack pointer and restore it before executing SYSRET.
IF (CS.L ≠ 1 ) or (IA32_EFER.LMA ≠ 1) or (IA32_EFER.SCE ≠ 1)
(* Not in 64-Bit Mode or SYSCALL/SYSRET not enabled in IA32_EFER *)
THEN #UD;
FI;
RCX ← RIP;
(* Will contain address of next instruction *)
RIP ← IA32_LSTAR;
R11 ← RFLAGS;
RFLAGS ← RFLAGS AND NOT(IA32_FMASK);
CS.Selector ← IA32_STAR[47:32] AND FFFCH (* Operating system provides CS; RPL forced to 0 *)
(* Set rest of CS to a fixed value *)
CS.Base ← 0;
(* Flat segment *)
CS.Limit ← FFFFFH;
(* With 4-KByte granularity, implies a 4-GByte limit *)
CS.Type ← 11;
(* Execute/read code, accessed *)
CS.S ← 1;
CS.DPL ← 0;
CS.P ← 1;
CS.L ← 1;
(* Entry is to 64-bit mode *)
CS.D ← 0;
(* Required if CS.L = 1 *)
CS.G ← 1;
(* 4-KByte granularity *)
CPL ← 0;
SS.Selector ← IA32_STAR[47:32] + 8;
(* SS just above CS *)
(* Set rest of SS to a fixed value *)
SS.Base ← 0;
(* Flat segment *)
SS.Limit ← FFFFFH;
(* With 4-KByte granularity, implies a 4-GByte limit *)
SS.Type ← 3;
(* Read/write data, accessed *)
SS.S ← 1;
SS.DPL ← 0;
SS.P ← 1;
SS.B ← 1;
(* 32-bit stack segment *)
SS.G ← 1;
(* 4-KByte granularity *)All.
#UD The SYSCALL instruction is not recognized in protected mode.
#UD The SYSCALL instruction is not recognized in real-address mode.
#UD The SYSCALL instruction is not recognized in virtual-8086 mode.
#UD The SYSCALL instruction is not recognized in compatibility mode.
#UD If IA32_EFER.SCE = 0. If the LOCK prefix is used.
Source: Intel® Architecture Software Developer's Manual (May 2018)
Generated: 5-6-2018